“front wheel electric bike kit +electric bike batteries for sale”

Thanks for your kind words about my article, I’m glad it helped! To answer your question, I highly recommend avoiding a custom built charger. While it might be possible to use a DC-DC converter to change the output voltage of your 12V charger, the chances of a problem occurring are too high for my liking. The converter might not be smart enough to adjust the current down once full charge is reached. Technically your BMS should protect your battery from most overcharging scenarios, but if it is overloaded and a component fails, there is nothing to stop your cells from being destroyed.

1 x 24V 500W Motor Brushed Controller. Electric Bike scooter twist throttle accelerator with power display, 5Led battery indicator. Motor brushed controller for Electric bicycle & scooter. Qty: 2PCS (…

If you are thinking about building your own LiPo pack, a 48V / 10-Ah battery pack can be made for around $300. However to undertake this project you should research extensively on www.endless-sphere.com on how to build and take care of your pack. Expect hours of reading before you are ready to build a pack of your own.

When you purchase one of our electric bike kit models, you can be assured of both quality and dependability. Let Monster Scooter Parts make your ride smoother and more enjoyable with a new electric bike kit.

As an aside, the 50A-800A you’re talking about is during the output, and that’s at a very low voltage, which is the reason for the high current draw. But that power equals a much lower current on the input end where it draws from the wall outlet.

Great article! Have ordered everything BUT i have a big problem with the batteries electrical Most homes in europe are limited to 10A and this spotwelder alone drags 15A just to powerupp!!!! I can even start it without blowing both fuses! And when welding it wants 50A-800A which you need a an actual POWERPLANT for!

Do you think it is the BMS or the controller that is cutting out beyond a certain load or something else completely? As far as I am aware the battery is fully charged and balanced (I even left it charging for 2 days once as I read that it can sometimes take this long to balance the cells!).

When it comes to welding your parallel groups in series, you’ll have to plan out the welds based on your welder’s physical limits. The stubby arms on my welder can only reach about two rows of cells deep, meaning I will need to add a single parallel group at a time, weld it, then add another one. If you have handheld welding probes then you could theoretically weld up your whole pack at once.

thanks for detail explanation , I was enjoj reading it. Well, I am interesting why did you pick this tipe of battery, I was thinking to use LiFePO4, I know there are usualy 3.2V it is less than 3.6V like here? Also, can you explain me how to calculate max current of battery, it says that you get 8.7Ah, but how much Ampers and what is the power of battery, how many Watts (P = U * I)? Furthermore, without welding, can I do on contact connection, like for example are battery in remote control?

The second big change is that the motor now runs at 48V, making the motor both accelerate and regenerate much more efficiently and powerfully. Finally, the fit and finish of the Syno-Drive has been considered from the perspective of service. Instead of a bolt-on axle, the Syno-Drive uses a modern thru-axle for added rigidity and easy removal.

I’m planning on building a 10S12P pack for usage on a custom DPV (Diver Propulsion Vehicle). For packaging purposes, it would be best for me to split the battery pack in several battery modules instead of a single block of cells.

A premium folding electric bike with Bosch drive system and leading warranty, sturdy and quiet with plenty of adjustability (seat post height and stem angle), smart accessories help you carry gear and stay dry without noise. The folding joints are thick and sturdy but don’t have sharp edges, both latches have……

Court- Excellent article (and I have read a lot). I wonder if you can weigh in on a system I am trying to build. I have a Montague Paratrooper (a bike that folds). I need to fold it and put it in a drift boat. It needs to weigh as little as possible and must have a removable battery and about a 10 mile range with an average speed 20+ mph. I had sort of “settled” on a Bafaang 750 or 1000 watt with Dolphin 52V battery (kit at Lunacycle). Now I am not so sure after reading the pro/con of your article. Cost is certainly an issue and ease of installation. I have been biking with out the motor, and I have numerous fairly steep (6-8%) hills. What do you think I should do? Rear hub, smaller battery. Thanks !

“Greetings, thought you may like to see an article about a scooter made using parts supplied by your company. It won first place in an engineering competition. Thanks for your help, and the fast delivery of the great parts!” – Dan from Tracy, CA

What are some inexpensive controllers that can send more power to the GNG mid drive? I saw some guy on YouTube claiming that he got a $30 controller that handles 35-45 amps. I don’t see any $30 controllers on eBay.

The Bosch mid-drive motor system has quickly become the leading motor system in Europe since its debut at Eurobike in 2010. Bosch’s quick success can be chalked up to many things, but perhaps most important has been its renowned reliability and performance. By building on the middle motor pioneered by Panasonic in the mid-90’s, Bosch started with an efficient and reliable design. But Bosch improved upon what Panasonic had been doing in important ways: adding more sensors (torque, cadence, and speed), a single chainring design like Impulse, for better reliability, and designing an advanced console for better control.

I bought a 2015 GNG mid drive, and the clutch in the crankset freewheel stopped working within a week with barely any riding at all, and I wasn’t even pedaling that hard. Pedaling now does nothing. I emailed GNG, and they told me to disassemble the clutch, and that would fix it. Anyone else have this problem?

ElectricRider has been a leader in the ebike industry since 2002, manufacturing and selling only the most reliable products on the market in order to share with our customers the absolute joy of real electric transportation! Lithium ion batteries are just one of our specialties, including FREE custom designing to fit your battery in the triangle of your frame, custom cases, etc. ElectricRider services/supports ALL products we sell, and our knowledgeable staff can answer any questions you may have, If you would like some guidance, call or write us so one of our ebike or ebike battery specialists can assist you.

Rated power: 1000W. To the motor to work at least first connected to the first four connectors, the first controller on the two thicker blue and white lines connected to the motor, in which the blue l…

9. Terms: Electric Bike Technologies LLC reserves the right, in its sole discretion to cancel, terminate, modify or suspend the Sweepstakes should (in its sole discretion) a virus, bugs, non-authorized human intervention, fraud or other causes beyond its control corrupt or affect the administration, security, fairness or proper conduct of the Sweepstakes. In such case, Electric Bike Technologies LLC may select the recipients from all eligible entries received prior to and/or after (if appropriate) the action taken by Electric Bike Technologies LLC. Electric Bike Technologies LLC reserves the right at its sole discretion to disqualify any individual who tampers or attempts to tamper with the entry process or the operation of the Sweepstakes or website or violates these Terms & Conditions.

One of the most affordable recumbent tadpole trikes I’ve tested, you do have to pay an additional $350 for shipping but it comes “ready to ride” so you can hop right on. The 48 volt battery supports increased power and higher speeds for the 500 watt internally……

One of the only full suspension electric cargo bikes I’ve tested, the suspension is adjustable and provides a lot of comfort to you and your cargo when paired with the premium Schwalbe tires. Excellent safety features including integrated LED lights, the headlight points where you steer and has……

Our range of electric bike parts includes OEM parts from Currie Technologies, the top dog of the electric bike industry. Currie Technologies is the manufacturer of the eZip and IZIP lines of electric bicycles, making them ubiquitous with quality electric bicycle products. Currie Technologies produces many (but not all) of the electric bike conversion kits that Monster Scooter Parts carries. No matter how you approach it, Currie Technologies is the brand to get when purchasing electric bicycle parts. In addition to the Currie Technologies parts that Monster Scooter Parts carries, we also carry electric bicycle motors and electric bicycle conversion kits from the Golden Motor Company. Golden Motor electric bike kits are customizable to almost any application, making them a good fit for the Do-It-Yourself electric bike enthusiast.

The Panasonic mid-drive motor is a remarkable bit of engineering. The basic motor design has stayed the same since the early 90s, when Yamaha and Panasonic began building drive systems for pedal assist electric bicycles. What has changed dramatically is the battery technology, which has allowed the Panasonic drive, which since the beginning was extremely reliable, to get better and better, offering riders more power and better range per charge. Today Panasonic remains a top-tier electric bicycle drive manufacturer being spec’d on a wide range of bikes from companies such as Kalkhoff, Focus, Raleigh, KTM, Helkama, and BH Easy Emotion.

torque sensor: the rear hub mount, a spring loaded chain sensor or bottom bracket flex as the rider pushes on the pedals and crank arms which sends a variable output for more or less power to the controller and motor

A few years ago I bought a vintage peddle-cab for transporting my mother in law around, as she has to be on oxygen. We love it, and it is great, however, it only has one gear, so the slightest hill can be a challenge. I’m hopeful to add an electric motor to this bike this winter. Myself, my daughter and a neighborhood kid would like to build this in the back room of my house. So far I think I need a mid-drive motor and 24V lithium batteries. I looked at your recommendations here, which one would you recommend for my peddle-cab? Also I am looking for user friendly and economical. Any helpful suggestions in this project would be greatly appreciated!

The Panasonic 18650pf is a good cell, that’s the one I used here. I also like the Samsung 26F, though it’s a fairly low power cell, and the Samsung 29E which is a bit higher power cell. The Samsung 30Q is a fairly new cell that has good specifications but doesn’t have as long a life – everything is a trade-off.

“e-bike motor lithium ion battery for electric bike”

It’s always hard to say exactly how much AH’s someone will need because every case is different. With that powerful motor sucking lots of juice and big hills though, you are going to want a minimum of 48V20AH. If I were you I would try to go even higher, but it may be even better to simply have two batteries at that point. It’s annoying to swap them, but if you ever had a problem with a 48V30AH battery that destroyed the pack, it would be a big investment straight to the garbage. A problem in one of your smaller packs would mean you still had the other. It’s not likely to happen, but it’s something to think about.

Great questions Charles and I have no idea! Sounds like a cool project and I bet people in the Stromer forums could help you with tips. I heard the ST1 models could be unlocked to go faster but I have less experience with the ST2. Adding a front hub motor would be really neat but make sure it works with the larger thru-axle or consider swapping the fork. I think adding suspension would improve the ride a lot and enable a front hub motor but not sure how you’d wire in a second battery or whether you could use the existing one? Would love to hear how it all turns out or see pics someday 😀

One of the biggest questions about electric bikes is “What’s the difference between motors?” and that’s because there are several different types including geared and gearless hubs, mid-drives and shaft drives. Not to mention brushed and brushless… I’m hoping this post can help to clarify the space a bit so you can focus in on finding the right ebike for your intended use.

Disagree, hubs can be much quieter… some offer regeneration and they area all easier on the chain and sprockets. For a hardtail trail bike or road bike they work really well and tend to cost less. Each technology offers some great benefits 🙂

The current GNG is much better than the GNG it replaced. GNG addressed the weak points of the previous model and updated its looks. The Lightning Rod unit may have been an awesome upgrade last year, but now the game has changed.

This kit http://huntneqip.com also been run at 72V X 30A = 2,200W/3-HP (with a different controller), but be aware that this level of power requires a swap to a chain primary reduction, or a wider belt. Also, the GNG allows for a stronger crankset to be swapped-in for riders who like radical jumps without bending the spindle (the BBS02 crankset cannot be upgraded).

Only charges Internal BTR2 battery / Will not charge External BTR1 battery. Note : All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions.

What a great article! It has opened my eyes to lots of possibilities. Being new to this I had a couple of questions. I am interested in building a spare battery to give me more range on the Faraday Porteur. My question is how to connect the battery I would build to the bike. The main battery resides in the downtube and the connection is hidden. They offer an ancillary battery that plugs into the charging port which is what I would like to build myself rather than buy. Do you think this would be possible? Where could I find a connector that would match? Any concerns? If so, what other options do you suggest? Thanks so much for the help!!

I use white 2mm thick craft foam and cut out a shape slightly larger than my pack. I wrap it up and seal it with electrical tape. It doesn’t have to be pretty, it just has to cover the pack. Your next step will hide the foam from view.

Description: Use this 1000W 48V 26″ electric bike conversion kit to transform your bike and eliminate the need for purchasing a brand-new electric scooter. The motorized wheel, electric controller, …

In some cases a front mounted hub motor is preferred because it allows an internally geared hub or continuously variable transmission CVT hub such as the NuVinci to be used in the rear. Some of the newest electric bikes like the Smart ebike combine an internally geared hub (that the cyclist pedals) with a hub motor and are able to put both in the rear wheel.

Hi Court, Love your work. It appears that you have one of the best jobs going! Just wondering if you are considering reviewing the 2016 KALKHOFF INTEGRALE 8 any time soon? If so I would be interested to hear the noise level of the Impulse EVO RS mid drive system coupled with the Gates belt as I intend to commute 75 km per day and want a really quite and fast commuter

Hi Pâmini! Yes, I’ve definitely been planning to review the Spicy Curry and I agree with you that the smaller 20″ rear wheel helps to improve balance. It also improves power because less torque is required to turn a smaller wheel. For the price, it seems like one of the best options. You can see my thoughts on the TranzX mid-drive motor by watching this review of the IZIP E3 Peak which uses the same setup. I admit that I do not like this drive system quite as much as Bosch but it is getting better and for the price it is quite good. I hope you and your girls have a blast riding whatever bike you choose and maybe in time you can let one of them tag along with a trailer like this that teaches riding. Also, here’s a video I made a while back that teaches the balance for riding a bike on your own 🙂

The Stromer ST1 uses a direct drive hub motor (like Bionx) made by the Taiwanese company TDCM. TDCM focuses on the development and production of electric drive systems for electric bikes as well as for other applications—including medical devices, starter systems, and wheelchairs, to name a few.

Output Power: 1800W. rated power: 1800w. 12/24/36/48v Universal Electric Scooter Twist Throttle Grip Universal 12v 24v 36v 48v Black Electric Scooter Bike Throttle Grip. Electric brushless Motor Type …

Now this step is very important: I’m going to turn the pack upside-down and perform this set of welds between the positive caps on the second parallel group and negative terminals on the third parallel group. Essentially, I’m welding on the opposite side of the pack as I did when I connected the first two parallel groups. Skip down a few pictures to see the completely welded pack to understand how the alternating side system works.

I figured this would be a critical step I wouldn’t want to mess up. Thanks for the advice on using the multimeter. That’s good to know as I thought I might need to open up the controller and see which wires went where on that male xlr connection which I guess would be an option too. Thanks again!

You’ll notice that for my charge wires I used larger diameter wires than the sense wires that came with the BMS. That’s because charging will deliver more current than those sense wires will. Also, you’ll notice the discharge wires (including the B- pad to the negative terminal of the pack) are the thickest wires of all of them, as these will carry the entire power of the whole pack during discharging. I used 16 awg for the charge wires and 12 awg for the discharge wires.

If you want a LiPo battery pack, one of your better choices if you want to save money and have a lot of output amps is build one of your own from a Hobby King packs. This requires a lot of time and knowledge, not only in building the pack but also in managing it.  LiPo batteries can be extremely dangerous and prone to burst into fire if not assembled with a lot of precautions (BMS) and cared for properly.

A fun, classic looking electrified tricycle designed for adults, it’s easy to mount, stable to ride and very adjustable in terms of speed and power, (go from 3 mph to 14 mph or slow reverse). Includes a rubber-coated metal basket that’s perfect for storing groceries, supplies or the included charger……

“bicycle battery motor kit _electric motors for bicycles”

The Bosch Performance Line motor is an electric bike drive systems that offers a balanced mix of performance, range and reliability. The design of the Performance Line system allows the motor to give you peak torque in each of your gears, making for great hill climbing ability with low power usage.

To develop a new hub motor would cost over $500,000 in tooling costs for a factory in China. Thats why even though there are many hub motors around for E-bikes, most are the same types or clones of existing types. Here is a list of known acceptable qualty hub motors available as of March 2012.

Give your kids the spirit of adventure and let them feel the wind fly through their hair as they cruise around on their Soozier electric scooter. With a top speed of 7.5MPH, they’ll be able to get to …

I’m a little worried that your batteries aren’t what you think they are. If they really are AA sized, which is rare http://electricbicycletechnologies.com the lithium battery world, then they are not 3,000 mAh. Next, 10 cells in series is going to give you 36V, which is twice what your 18V drill is rated for. 5 cells in series and 2 in parallel would be a better method. I usually recommend a BMS but you can skip it if you have another way of diligently monitoring your cell voltages and then charging using an RC style balance charger like an iMaxB6 charger through an JST-XH connector.

Cheers Court! Maybe you have some insight into a great question a friend asked me: “If there were a scientific experiment done where all variables were the same with the exception of the drive motor, one being a mid drive and the other being hub drive (both of good quality and used on higher end mainstream e-bikes), is there a clear winner when it comes to which drive system delivers more efficient power. I guess what I’m hoping to find out with this question is: Which style of drive system more efficiently transfers the potential energy in the battery into actual motion. I could see this being answered with units like distance or speed, but remember the only thing I am comparing is two types of drive systems… Things like battery size, pedaling effort, rolling resistance, total bike/rider weight, air friction are all constants. So is there a clear winner???”

I’m not familiar with this copper serial connection you’re talking about. I guess you mean to reinforce the series connections to handle more current? As long as you are using enough strips of nickel (and ensuring that it’s pure nickel and not nickel coated steel) then you shouldn’t need copper reinforcements. I try to use at least 1 strip of nickel for every 5A my battery will carry. So if I’m looking for a 20A max load, I’d use 4 strips of nickel in each series connection. That’s easy to do if each cell in a parallel group of 4 cells is connected to the next group by one strip each.

A very affordable 13S BMS that I like is this 30A version, though it can take a few weeks or even a month to arrive since it’s coming all the way from China. http://www.aliexpress.com/item/13-lithium-battery-protection-board-48v-lithium-battery-BMS-30A-continuous-60A-peak-discharge/1741121963.html

“Greetings, thought you may like to see an article about a scooter made using parts supplied by your company. It won first place in an engineering competition. Thanks for your help, and the fast delivery of the great parts!” – Dan from Tracy, CA

Modern E-Tube networking: the wireless Di2 EW-WU111 by Shimano. The EW-WU111 can be connected with your smart phone, tablet or PC and once connected it shows the gear and the current battery status. The connection between the two devices is made over the new E-Tube App via Bluetooth®.

This new kit uses the same motor as the GNG. It also uses the same basic configuration, with a quiet belted primary reduction in the high-RPM half of the drive, and a narrow and strong chain in the lower-RPM half of the drive.

Author’s note: Hi guys, Micah here. I run this site and wrote this article. I just wanted to let you know real quick about my new book, “DIY Lithium Batteries: How To Build Your Own Battery Packs” which is available in both ebook and paperback format on Amazon and is available in most countries. It goes into much deeper detail than this article and has dozens of drawings and illustrations showing you every step of designing and building a battery. If you find this free site helpful, then taking a look at my book can help support the work I do here to benefit everyone. Thanks! Ok, now back to the article.

Suitable for electric bicycle & scooter, mechanical or electric forklift. Speed governor :Thin green (Speed handlebar Signal input) /Thin black (Negtive Power) /thin red(5V Positive Power). Ignition S…

The stokemonkey is only for long cargobikes like the Yuba Mundo, Xtracycle Edgerunner, and Surly Big Dummy, but…if you actually haul cargo, this drive absolutely conquers hills when you are fully loaded. They are still available in the classic edition (where the pedals turn when the motor is running) but now…they also have a freewheeling crank option. This system has recently been upgraded, and is now sold by ebikes.ca

Warning: if a cheap electric bike is advertised and the advert does not state what kind of battery it has, you can pretty much be certain that it has a lead-acid battery. It might be cheap, but it’s not a bargain. This battery type might be good enough if you want the bike as a mere toy, to be taken out and played with occasionally in your immediate neighborhood – but if not, it would be better to avoid these batteries altogether.

Our range of electric bike parts includes OEM parts from Currie Technologies, the top dog of the electric bike industry. Currie Technologies is the manufacturer of the eZip and IZIP lines of electric bicycles, making them ubiquitous with quality electric bicycle products. Currie Technologies produces many (but not all) of the electric bike conversion kits that Monster Scooter Parts carries. No matter how you approach it, Currie Technologies is the brand to get when purchasing electric bicycle parts. In addition to the Currie Technologies parts that Monster Scooter Parts carries, we also carry electric bicycle motors and electric bicycle conversion kits from the Golden Motor Company. Golden Motor electric bike kits are customizable to almost any application, making them a good fit for the Do-It-Yourself electric bike enthusiast.

2x Motor Gear Box 12V For Kids Ride On Car BMW Audi TT Hummer Land Rover Jeep. This pair of gear box is suitable for 12V Ride on Hummer, TT, BMW, Mini, Jeep and Land Rover etc. Sub-Type:Battery/ Electric.

NYCEWheels has some of the best bike accessories you’ll find anywhere, whether you’re looking for accessories for electric bikes or for standard bikes. Our accessories can improve your safety, ease your commute or just help you fix your bike. We… learn more

I’ve been reading a bit about how Batterybro.com makes sure to test there batteries are genuine, and how it seems they still get a lot of fake batteries from China. When you buy on Aliexpress.com how to you know and make sure the batteries you buy are genuine? there’s a lot of sellers how did you find yours?

Bafang (8Fun) is a Chinese manufacturer of electric bike motors. Bafang is one of the world’s largest producers of motor systems, primarily front hub geared motors for the European market (primarily the Netherlands). Besides front hub motors, Bafang also produces a range of rear hub drives, a simple mid-drive motor, and ebike components such as consoles (HMIs) and battery packs.

At the same time though, think about if that is what you want. It could be that those cells died because of a malfunctioning BMS unit or old wiring. Putting new cells in their spots could just wind up killing those new cells in a few days or weeks. I’ve seen that happen as well. So make sure you check everything and consider all of your options!

One of the most affordable recumbent tadpole trikes I’ve tested, you do have to pay an additional $350 for shipping but it comes “ready to ride” so you can hop right on. The 48 volt battery supports increased power and higher speeds for the 500 watt internally……

Most of the price involved these days in building an e-bike or buying a ready to go e-bike is the size and chemistry  of the battery pack. For the consumer its important to understand  the difference between a 24V, 36V, and 48V pack. Also know what a 10-Ah pack is compared to a 5-Ah pack.

Amounts shown in italicized text are for items listed in currency other than U.S. dollars and are approximate conversions to U.S. dollars based upon Bloomberg’s conversion rates. For more recent exchange rates, please use the Universal Currency Converter

BMS’s aren’t required, they just make life easier. As you mentioned, if you don’t use a BMS then you’ve got to diligently monitor your cells and use balance charging to manually balance your cells. A BMS just takes care of this hassle for you. A low quality BMS can cause problems, but good quality BMS’s shouldn’t risk cell damage.

Original Shimano parts guarantees that all components work perfectly for optimum performance and maximum safety and longevity. This Shimano Cycling small part is known as: IBBR9100B. It has a UPC of: …

“e bike batteries |which electric bike”

36V 500W Brush motor Controller Box For Electric Scooter Bike. This 36 volt controller has 8 connectors. Red, Black & Blue: Speed Regulator 1-4 V(Throttle ) (Red: 5v,Black: – ,Blue :Signal Wire). Red …

Hi Craig! Sorry for the delayed response here… extremely busy times including some family stuff going on right now. Given your mostly road + a bit of gravel and the desire to go fast and far I’d recommend the Focus Thron Impulse Speed… This thing goes up to 28 mph, has a range of 100+ depending on the assist level you use, offers slick but cushy tires for road but also has full suspension for a bit of trail. Given your height, this bike would offer an excellent fit because it comes in four frame sizes and you’ll get a lot of utility with the integrated lights and mirror for those longer rides which might expose you to different times of day and busy traffic. Your idea about adding an aftermarket bar is a good one and I’ve done just this on a hybrid Trek I used for commuting in Austin years ago. You could explore stems that are shorter and more angled (upwards) and bars that are swept back a bit so you don’t have to lean forward as much. The full suspension should really help with your back and neck and is very nice to have when riding at higher speeds for longer time periods. Honestly, 100 miles is a long way to go so I wouldn’t bother with an extra pack right away, feel your way into it because I’m sure it will be $700+. As for your wife, there are very few electric recumbents available. It seems that many people use a kit to convert their trike and BionX has been popular because it’s available in many wheel sizes, offers throttle and assist and has regeneration. As an alternative, you could explore the Ridekick Power Trailer but it’s much noisier than the gearless hubs from BionX. Either of these options allows you to choose the perfect bike first and then go electric. I hope this helps! The Stromer ST2, Specialized Turbo, Easy Motion Nitro City and IZIP E3 Dash are also good speed pedelecs but http://electricbikecharger.com get the same range or offer the same comfort as the Focus Thron.

Hi Danl, that sounds like a very high power motor. Most consumer ebikes are in the 36V-48V range, so if your motor is advertised as being rated for those higher voltages then it’s definitely a more serious motor. If you’re looking for a ready-built and relatively inexpensive battery, then something like this might work for you, though I haven’t personally used that battery. You can of course build your own battery just like I did in this article, and that way you’ll be sure to get exactly what you’re looking for. The AH’s required will depend on the quality of the battery. A batter rated for higher current will require fewer AH’s than a lower quality battery. I’d aim for at least 20AH, if not more on a motor of that size. It’s going to eat your battery quickly, so you’ll want more capacity to be able to ride longer.

For dd hubs, i think a big drawback is the cogging torque when pedalling unassisted. It may be unnoticable at 5-10mph, but trying cruising at a normal 15 mph and it has “flat” feeling. Freewheel in geared huib abd mid drives roll magnet -free and that should be mentioned, imo.

The Active Line drive is designed for casual, comfortable cruising and pairs particularly well with bikes equipped with an internally geared rear hub. Featuring the full suite of sensors – including cadence, speed, and torque, the Active Line offers great hill climbing torque for moderate to steep hills. The Active Line drive offers a maximum assist speed of 20 mph.

I am on his build list, in part due to the positive reviews here and on endless sphere. Hopefully I’ll have one in my hands in a while and will be able to truly evaluate whether it was worth the additional cost.

1C charging is too high for most Li-ion. It’s too much to ask for right now, to be able to charge an entire pack in one hour. It can be done, but it’s not healthy for the cells. Aim for 0.5C at the most. I usually don’t go past 0.3C on charging.

Also changing the fuse to a higher one could cause the wires to start a fire and the whole house would burn down if the wires are not thick enough. Also in sweden a fuse gets bigger as they are rated higher so you can fit a 20A fuse in a 10A slot, for safety.

I want to take the apart and use the cells to make a 48V 16.8ah battery. Would you advice against this? Would 48V provide a noticeable difference in the power of my motor? (It is a 500W Falco Direct Drive Hub Motor)

That’s exactly correct. You’d start by welding 10 parallel groups of 4 cells each, then you’d connect those 10 parallel groups in series to make one rectangular battery. I’ve done many 10s4p packs just like that for 36V 10ah ebike batteries.

Hi Craig, sounds like a fun setup! Honestly, power and efficiency are very difficult to calculate on ebikes because some motors list a nominal and peak while others do not. There is a potential leverage boost from a mid-drive like the Optibike has but it really depends on the system. The Pioneer series is much more basic than their R Series or something like the Bosch Centerdrive or Impulse 2.0 but that doesn’t mean those are more powerful, just more responsive. I do my best to provide an overview on here but I’m not able to actually compare “power” and usually don’t even get to find out the Amp rating on the systems. Knowing the motor wattage and battery voltage is a start… along with the motor type, but that only goes so far. I’m sorry, I guess trying it out is the best way to decide for yourself.

I’m sorry to hear about your bad experiences with AliExpress. I’ve done a lot of business there, and I’d say only around 5% of my transactions have been problematic. They have great buyer protection though and every time I’ve either gotten a full refund or had my product replaced at no cost. If you want a BMS from a source other than AliExpress or eBay, I recommend a company called BesTechPower. They make the highest quality BMS’s I’ve seen and they are the ones I use on my “top shelf” batteries. They are pricier, but you definitely get what you pay for. Just email their contact addresses and they can help you choose a BMS. http://www.bestechpower.com/

Thanks so much for the info, that sounds great and an exciting option! I understand the warranty issue but aside from that, you don’t see any issue than with building a battery of any capacity and just making the discharge cable with an xlr connection to plug into the bike. Would I need a different cable to charge the battery or does it charge via the xlr connection like theirs? Here is one more link with a few more answered questions about their auxiliary battery if you wanted more info. Thanks again, this is really exciting, I just want to make sure I don’t fry anything

“electric a bike _bicycle electric conversion kit”

If you have time, I’d be curious to hear about the pros and cons of this kind of approach. Is the main drawback simply the cumulative size of the plastic housing? Or is there some other limitation to this kind of hardware that makes it unsuitable?

One of the most powerful, fastest accelerating, quietest, and beautifully designed electric bikes I have ever tested, premium drivetrain and custom battery. Surprisingly lightweight and well balanced front to rear considering the large 750 watt hub motor,……

3. i saw 18650 and 26650 li ion batteries which are more powerful such as 6000 – 8000 mah. i think they are fake??? i need 48v 10ah or 20ah minimum i guess as a pack ??? your advices are important. thanks for all…

Agreed, I have two (2) Ecospeed units (one on a EZ-tandem, one on my RansV2) and they perform flawlessly. Their (intelligent) VRAP motor controllers give more range than any comparable controller at higher power levels.

The SLA electric bike battery is a reliable power source for electric bikes that are used for shorter trips. The best lifespan for an SLA battery is obtained by keeping it fully charged as much as possible, and discharging it only to half its actual capacity. It’s an affordable electric bike battery, ideal for round trips of 5 to 8 miles, when it can be recharged right away. In typical electric bike use, SLA electric bike batteries last about a year, but longer life is possible if the use is very light, and the battery is kept fully charged at all times.

36V 10ah Lithium battery (Included with the battery is the charger and mounting Bracket). Standard 26 in by 4in Front Wheel 500w brushless motor hub ( disc brakes). Pedal Assistance system included ( …

I’d recommend going with a cell that can output 10A, giving you 40A continuous power rating. You’ll use less than that, meaning the cells will be happier (and cooler). Something like the Sanyo 18650GA or LG MJ1 would give you good power and capacity (both are around 3,400 mAH per cell).

I am looking to purchase my first electric bike. I have test ridden many and narrowed my favorites to the eMotion City Wave and the Pedego City Commuter, with 28″ wheels. I don’t anticipate lengthy trips – likely up to 30-40 miles tops, however we live in the hills of NH, so I would be using pedal assist and/or throttle for the tougher climbs. While I love the City Wave ride, I worry a bit about the 350W vs. the possible 500W on the Pedego. I am 5’8″ and weigh 138 lbs. Your thoughts?

You’ll also want to test out the battery with a fairly light load in the beginning. Try to go for an easy ride on the first few charges, or even better, use a discharger if you have one. I built a custom discharger out of halogen light bulbs. It allows me to fully discharge my batteries at different power levels and measure the output. This specific battery gave 8.54 Ah on its first discharge cycle at a discharge rate of 0.5c, or about 4.4 A. That result is actually pretty good, and equates to an individual average cell capacity of about 2.85 Ah, or 98% of the rated capacity.

I’m not sure what cells exactly you’ve got there, but a good replacement cell (assuming it has similar specs to your cells, which you’ll have to confirm) could be the Samsung 26F cell. It’s a good quality economical battery cell. I’ve gotten them from here and had great experiences with the vendor: Samsung 26F 18650 lithium battery cells

Regarding the cell question, its a mixture of both. Cheap ebikes use cheap cells. You can bet the Sonders ebike had the cheapest cells available. Name brand ebikes usually use Samsung cells, but sometimes LG and occasionally Panasonic cells can be found in name brand ebikes (the Panasonics are some batteries electric bikes the most expensive and so they are rarer). That being said, I’ve seen some shadier internet sites selling high quality (and genuine) Samsung/Panasonic packs, and I’ve seen some nice ebikes with some no-name cells. You should always check with the vendor/manufacturer if you want to ensure you’re getting good cells. Unfortunately, it can be hard to verify the cells yourself though without voiding the warranty, as they are usually sealed under shrink wrap. A good vendor will be happy to confirm the cells for you ahead of time and may even be able to show you some pictures of opened packs to verify.

We distribute the X-Treme E-Bike brand of power assisted electric bicycles, electric bikes, electric mountain bikes, electric beach cruisers and folding electric bicycles. We do not sell “single electric bicycles” retail to the public but we do offer replacement parts to everyone. Shoppers, click Store Locator to find an X-Treme Electric Bicycle Authorized Dealer near you.

Hi Pete! I did really enjoy the Neo line and it seemed like they sold a lot of them so hopefully there will be packs available for several years. Considering that the same pack was used on all of the different models, I feel like you should be in great shape 🙂

My series connections are between each group of 3 parallel cells. So all the connections that go across the short side of the pack are parallel connections, and all the connections that run along the long end of the pack are series. It doesn’t always happen that way, but the shape of this pack forced that geometry.

The TDCM configuration on the Stromer ST1 is an exclusive design for Stromer. The heart of the system is a direct drive, brushless motor featuring a nominal wattage of 500 watts and a peak torque of 40Nm. The TDCM motor is a large motor that, while heavier than other motors such as Bionx, benefits from less sensitivity to heat buildup when climbing.

Note that in the article it says that LiFePo is the most commonly used chemistry. I think that depends on where you are looking. I suspect that LiNiCoMn or the older LiMn is actually most common in terms of total unit cells because they’re the cheapest and get used in the low end E-Bike market in China.

I would advise against connecting one battery to the other’s charging port. That charging port, as you correctly stated, is wired to a charging circuit on the BMS which is usually meant to take 5A max, sometimes less, whereas the discharging side of the BMS usually puts out at least 15A, sometimes much more. You can easily fry your BMS by connecting a second battery to its charge port.

One other drive system that sort of splits the difference between mid drive and hub drive is the shaft drive. It works like an automobile, positioning the motor more towards the center of the bike while driving the rear wheel with a shaft. These are not very common today, perhaps because they require extremely customized frames that are not symmetrical. While a rear wheel drive truck often has a drive shaft extending from the motor (under the hood) back to the rear wheels that is located centrally under the body, a bicycle has to use one of the chain stay arms to support the shaft. This makes it look a bit awkward and perhaps difficult to service as well.

3. There’s something that I think you might be missing here. The factor that actually limits current draw is the controller, not the motor or the BMS. Those are “rated” for 500w and 15A, respectively, meaning they won’t overheat at those values. But both can physically pass those values if you force them to. It’s the controller that is actually “pulling” the current. So you should check your controller to see what its current limit is. If it is a 15A limit controller, then it won’t physically pull more than 15A. The fact that your battery can technically put out 1200W just means that it has “oomph” than you’re using, and you’re giving it an easy, healthy life. But if you switched to a 50A controller, suddenly you’d be pulling the maximum current that your battery can supply (and probably overheating your motor if you pull that 50A for a long time).

Having built a 13s4p battery to the best of my ability and hooked it up to my 48V 1000W ebike conversion kit…. the lights on the throttle turned on and the wheel spun! Initially I thought the project was a success but after mounting the battery and controller onto the bike and taking the bike for a test spin I ran into a major problem.

Electric Bike Conversion Kit Systems Now Available from one of USA’s Leading IBD Distributors Philadelphia, PA: Electric Bike Technologies USA, a manufacturer specializing in affordable high-quality electric bicycle conversion kits, announced that their EBikeKit ™ and E-TrikeKit™ systems are now available via J&B Importers. With J&B’s extensive network of authorized dealers, the conversion kit products will now be readily available throughout the country at most local bicycle shops. Of the…

You commented on the cost without commenting on quality or design or anything other factor. Not really fair. I can buy a house for twice as much as a another house, insane? Likewise you could find a car for twice as much as your current car – is that insane? Without examining the other variables (quality/features/etc) its not even reasonable to begin commenting on the cost.

By entering the Sweepstakes you agree to receive email newsletters periodically from Electric Bike Technologies LLC. You can opt-out of receiving this communication at any time by clicking the unsubscribe link in the newsletter.

Maybe another way forward is to buy a pannier mounted supplementary battery pack (a proper one with a BMS) and to install it in parallel with the main one. The question then becomes whether to connect between the sprung terminals that go to the motor controller (which I believe to be the best thing to do) or into the little charging port jack. I presume that the charging port is connected to the charging side of the BMS and I don’t know how much current that port would take or whether it’s even a good plan to charge and discharge the main battery at the same time. I see significant potential for a high current through that small jack once I discharge via the main battery and a voltage difference exists between the supplementary batter and the main battery.

Hi Om, most electric bike kits that I’ve reviewed don’t offer regeneration and those that do are incredibly inefficient (like ~20%) so you’re losing much more energy than you capture. It’s a neat feature for helping you slow down when descending big hills and it creates a nice feeling to think that you’re getting a charge but I would not set out to generate electricity by pedaling unless you want to simulate hills and use your bicycle for rigorous exercise. If that is your interest then check out the BionX kits which all offer regen, you can even buy them preinstalled on bikes from OHM and others.

The BMS I chose is a 30A maximum constant discharge BMS, which is more than I’ll need. It’s good to be conservative and over-spec your BMS if possible, so you aren’t running it near its limit. My BMS also has a balance feature that keeps all of my cells balanced on every charge. Not all BMS’s do this, though most do. Be wary of extremely cheap BMS’s because that’s when you’re likely to encounter a non-balancing BMS.

This new kit uses the same motor as the GNG. It also uses the same basic configuration, with a quiet belted primary reduction in the high-RPM half of the drive, and a narrow and strong chain in the lower-RPM half of the drive.

One question regarding the specific battery BMS you used in this build: It uses a different wire for charging vs discharging the battery. Does this mean that the regenerative braking feature cannot be used for this battery?

Hi Court, I have a 2005 Giant Trance 2 mountain bike I’d like to convert. I want to commute to work which is 15 miles away using trails and minimal road exposure. There is also a fair amount of hills. The trance has a small triangle and I fell I would need a fairly large battery. I see a 52 volt 20ah at Lunacycle that is a triangle that looks like it will fit but its $600. I’m leaning toward a 1000 watt BBSHD unlocked.. all of this said, I recently rode a fat bike with a BionX hub drive that was so smooth I couldn’t believe it. The BioniX battery would never fit the triangle. Any thoughts or guidance would be appreciated. Thanks

I am trying to decide if I need a 350 watt hub motor for a bike conversion or would a 500 watt hub motor be better. I weigh almost 230 lbs but live where there are minimal hills. My husband would be doing the conversion with an all inclusive kit. Does a person’s weight have anything to do with what size motor you buy?

For a 24V 7s pack, I’ve used this BMS a few times and been quite happy with it: http://www.aliexpress.com/item/7S-Li-ion-Lipo-Batteries-Protection-Board-BMS-System-24V-29-4V-20A-Continuous-Discharge-350W/32336397316.html

Hi, Court Rye! Thank you for your response . As I supposedly said, I do cca.20 km per day. 2000 – 3000 per year. The main road is straight, as well as highs. Just for them I need help of the engine. I send you pictures of the engine that are offered to me . They said that discourage hub motor ( in the first wheel ) , as well as the Mid – Bafang , because often corrupts !? So, what do you mean? Thanks and best regards, Miran

The safest and fastest growing lithium battery (LiIon) system for electric bike / bicycle  applications, offers high-energy density and low weight.It’s a kind of rechargeable battery, no memory effect.The three primary functional components of a lithium-ion battery are the negative electrode, positive electrode, and the electrolyte. The negative electrode of a conventional lithium-ion cell is made from carbon. The positive electrode is a metal oxide, and the electrolyte is a lithium salt in an organic solvent. The electrochemical roles of the electrodes change between anode and cathode, depending on the direction of current flow through the cell. The most commercially popular negative electrode material is graphite. The positive electrode is generally one of three materials: a layered oxide, a polyanion, or a spinel.

Cell Model Samsung 2900mah. BATTERY CELL -18650 Rechargeable Lithium Battery cell. It also comes with aUSB CHARGING PORT which can be used for charging your phone. Battery Type: Dolphin Type Lithium Battery.

“lithium ion battery for electric bike bolt on electric bike motor”

Lead-acid electric bike batteries are cheap and easy to recycle. However, they are sensitive to bad treatment, and they don’t last very long. They are not a good choice if you’re serious about actually using your bike to commute.

Give your kids the spirit of adventure and let them feel the wind fly through their hair as they cruise around on their Soozier electric scooter. With a top speed of 7.5MPH, they’ll be able to get to …

By 1898 a rear-wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel, was patented by Mathew J. Steffens. Also, the 1899 U.S. Patent 627,066 by John Schnepf depicted a rear-wheel friction “roller-wheel” style drive electric bicycle.[7] Schnepf’s invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his U.S. Patent 3,431,994. Wood’s device used 4 fractional horsepower motors; connected through a series of gears.[8]

Full suspension fat bike with a high quality mid-drive motor from Bosch and their updated 500 watt hour battery pack for extended range. Cool fluorescent paint job that extends all the way through the fork, rear shock housing,……

I’ve reviewed all of the bikes you mentioned including those from Pedego (which also makes one of the Ford Ebikes), Specialized and Flux. I disagree with your local bike shop about Pedego being low quality… some of the models are a bit basic and “classic” in terms of design but the company provides good support and honors their warranty, they even did a voluntary battery recall a year or so back which was proactive and upstanding. The downside there is going to be higher price and finding a local dealer.

We strive to provide the best price available on BatteriesPlus.com and in our stores. Store pricing may vary from the price advertised on BatteriesPlus.com. Fees may apply for recycling, environmental disposal, and/or labor/installation.

An affordable, powerful, electric fat bike with responsive 12-magnet pedal assist and twist-throttle on demand, available in two colors with lots of accessory options including fenders and racks. Only one frame size but the top tube is sloped and the shorter stem pairs……

I’m glad you enjoyed the article. To answer your questions: I chose this type of battery instead of LiFePO4 mostly because of the cost and convenience. LiFePO4 is a bit more expensive and has fewer options for cells. These Li-ion cells are a bit less expensive and there are dozens of options with many different specifications for any power/capacity need. I’ve used and built LiFePO4 packs before and they have their own unique advantages, but for me they just don’t add up to enough.

Hey Court – I would have replied sooner but I wasn’t notified you had replied, guess I will have to check this site more often. I never thought of a front drive system before, I will check it out. From what your article said, I think I can still pedal and probably need to to go up a 8% grade. I like the idea of being able to simply detach the battery and the hub when I put it in the boat. I am going to look around for a more powerful motor as I need to get it up to closer to 28 mph if possible. Just did the ride yesterday and let me tell you the whole way I was like, “need that ebike NOW” If you have any other thoughts let me know….. Thank you, Eric

My series connections are between each group of 3 parallel cells. So all the connections that go across the short side of the pack are parallel connections, and all the connections that run along the long end of the pack are series. It doesn’t always happen that way, but the shape of this pack forced that geometry.

As an aside, the 50A-800A you’re talking about is during the output, and that’s at a very low voltage, which is the reason for the high current draw. But that power equals a much lower current on the input end where it draws from the wall outlet.

Mass produced Hub motors out of China have made a huge impact on the electric bike market. There are a large number of E-bikes available on the market today because of the invention of the electric hub motor. Because of hub motors, E-bike manufacturers are able to use just about any bicycle frame to turn it into an electric bike. For better or worse, almost any company can choose to be an e-bike manufacturer thanks to the simplicity of hub motors.

A three-wheeled electric assist box bike designed to transport up to four children, includes a locking bench seat cargo cubby, full fenders and chain guard, optional canvas cover to keep the kids dry. Solid braking with two 160 mm mechanical disc brakes up front and a linear pull……

With pedal-assist the electric motor is regulated by pedalling. The pedal-assist augments the efforts of the rider when they are pedalling. These e-bikes – called pedelecs – have a sensor to detect the pedalling speed, the pedalling force, or both. Brake activation is sensed to disable the motor as well.

Since you mentioned the charger, the link you sent me came with a 2 amp charger but it would take 10 hours to charge that size battery. Could I use a larger amp charger like 5 or even more for faster charging? How do you tell what is too much so you don’t damage the battery? Thanks!!

Thanks again for the great info, that is really helpful. I just have one last question. On the XLR connections there is a hot, neutral and ground. It appears on the battery you linked to that there are just two wires, how can I ensure which prongs of the male XLR connection on the Porteur are hot and negative? Also, do I just leave the ground spot on the female XLR connection open since there is just a hot and negative wire?

Some e-bikes have an electric motor that operates on a power-on-demand basis only. In this case, the electric motor is engaged and operated manually using a throttle, which is usually on the handgrip just like the ones on a motorbike or scooter. These sorts of e-bikes often, but not always, have more powerful motors than pedelecs do.

What does that mean?. Well, it is like having another fit bicycle rider helping you pedal, but without their weight. No matter how hard your hills, or heavy your bike is, this motor will always work t…

If your electric bike isn’t giving you the range it used to, it might be time to replace its battery. Batteries Plus Bulbs has a wide variety of scooter and e-bike batteries that will give your ride new life. Just look for your specific model, then pick the battery you want.

I have been thinking of throwing in a 350W front hub motor as well (on a separate throttle) to be used only if and when the rear wheel digs into the really soft sand – to create a 2×2 wheel drive. I’m not worried by different speeds and power of the front and rear motors as they would only be used simultaneously very occasionally and then only if and when the the rear wheel is slipping badly. Regards, Len

Interesting… that’s a beefy looking electric bike! I haven’t heard of Falcon or tested this bike (or anything quiet like it) but the specs are impressive. Note that it’s actually not classified as an ebike due to the large motor, it would need to be 750 watts with a top speed limited to 20 mph, and this could create a liability issue if you crash and damage property or injure someone. Given your desired range, it seems like the super large battery pack would be good, it will impact weight and handling to some extent but that’s the trade, an alternative would be a mid-drive ebike with pedal assist like the Volton 350. Note that the Falcon website doesn’t have an address, just this phone number (855)-661-7337 so it feels less trustworthy than a local dealer or large company that is more willing to expose who they are and potentially offer ongoing support. Hope these thoughts help 🙂

TerraTrikes make great electric recumbent trikes. Here are a few how to tips for converting the Rover and Rambler models, specifically with internally geared hubs. The TerraTrike Rover and the rambler models both are offered with internally geared hubs. It is possible to convert the trike to external gearing, but you will probably want the help of a bike shop that is familiar with recumbents. For a good bike shop,…

Gearless hub motors may require a larger casing (in order to accommodate the magnets) and ultimately weigh more. This is of course a generalization because the technology has evolved to the point where some direct drive hub motors are quite small and lightweight.

Rated Capacity: 10Ah. Recommended to be used with 36V 250W electric bicycle motor. 36V 750W 20″ Front Tire e-Bike. Charge Current: 2A. Model: Bottle Type. 1 Year manufacturer warranty for CHARGER. Use…

Hi Om, most electric bike kits that I’ve reviewed don’t offer regeneration and those that do are incredibly inefficient (like ~20%) so you’re losing much more energy than you capture. It’s a neat feature for helping you slow down when descending big hills and it creates a nice feeling to think that you’re getting a charge but I would not set out to generate electricity by pedaling unless you want to simulate hills and use your bicycle for rigorous exercise. If that is your interest then check out the BionX kits which all offer regen, you can even buy them preinstalled on bikes from OHM and others.

My first question is whether a hybrid or a hard-tail mountain e-bike is best suited for my needs? Most hybrid models I have seen are set up for commuting and since I am a fair weather rider I have no need for added features such as fenders and lights. I do, however, desire the option to mount a rack. I love the versatility and looks of mountain bikes. Bull has a few HT mountain bike models (29ers and 27.5) that may work but wonder if the riding position may be too aggressive and/or the tires too wide (i.e., too inefficient) for riding on the paved road sections.

First off: the info you received about a the battery without a BMS blowing your controller is wrong. It’s always a good idea to use a BMS for safety reasons, but as long as the battery is balanced and fully charged, your controller has no idea if it has a BMS or not. All your controller cares about is if the voltage is correct, which as long as the battery is charged, then it presumably will be.

Finally found it. WOW!! Exactly what was needed. I struggle with conceptualizing verbal descriptions. You solved that! With the new JP Welder from Croatia my first welded build will soon be a reality. Thanks for all you do for eBiking!

Remove all metallic jewelry. This is another tip that I can give from experience. Arcing the contacts on your battery is not something you want to happen ever, and especially not against your bare skin. I’ve had it happen on my wedding ring and once even had a burn mark in the shape of my watch’s clasp on my wrist for a week. Now I take everything off.

Hi Micah, I have been studying your how to build an bike battery, and enjoyed all the tips. I have been having a bit of difficulty figuring out the wiring portion of the construct however. For example, you talk of C, B and P pads and wires you solder to the top and bottom of the pack; the yet don’t put arrows to or refer to their colors for easy identification. The charge and discharge instructions for connecting are gone over rather fast with little for us to identify with exactly where to attach to, etc. Could you revisit your post here and include some baby steps for those who can’t follow the reference instructions you give for wiring the BMS?

the problem i have and the bit im confused on is this, i understand the negative on the entire pack goes to the negative on the BMS and the positive of each parallel cells goes to each sense wire but where are the charge and discharge wires going ? am i corrrect in saying that the positive of the pack goes to the charge and discharge socket on the BMS and that when the pack receives its charge it charges the pack and the discharge is when the pack is under load from the output of the pack i.e what ever its connected to for example your bikes motor? in your tutorial you havent shown how you connected the parallel groups of batteries together in series to give you the final pack voltage and capacitance but i’m assuming you linked them in series to get the toal 36v but on the pictures the first and last cells are split compared to the doubled batteries for electric scooters canada cells you have through out. am i also correct in saying that if you have 2 batteries connected together to form a cell then you dont need a sense wire on each battery because the two batteries are considered to be the same battery and when they charge and discharge they equalize as one shunts the other ? sorry for so many questions i have googled and googled and googled and as Einstein once said the definition of madness is doing the same thing over and over and expecting a different result, many thanks in advance .

“lithium bike battery _motorized bicycle electric”

Most electric bicycle batteries fall into the 24V to 48V range, usually in 12V increments. Some people use batteries as high as 100 volts, but we’re going to stick to a medium sized 36V battery today. Of course the same principles apply for any voltage battery, so you can just scale up the battery I show you here today and build your own 48V, 60V or even higher voltage battery.

Thank you very much for quick answer. You give me a good advice and I will use it. To sum up, now I am on the cross Li-ion or LiFePO4, can you sugest me some othre examples like Panasonic 18650 which you tested and you clame are good batterys? For BMS, is there special tipe which are good or there is no different or just like you says it must be for a bit stronger etc. batterys give 30A we must have a bit stronger BMS like for 40A?

If I regroup my 12 paralled cells in 10 modules, can I then join these in series using single wires (one for neg, one for pos) between modules, instead of wiring each terminals of each cells like you are doing. Could this affect BMS and/or have any negative impact on cells balance?

How do you determine this exactly? Your battery is a 36v 8.7Ah and I guess it has something to do with the maximum continuous discharge rate. It would help me (and maybe others) to explain why 30A is more than enough for this battery.

Yes, that’d work, but I’d get an additional 7s battery so you have 20s total. Also, you should know that the older your original 48V battery is, the more time it will take your new 72V combined battery to balance, as the first 13 cells will likely have less capacity in comparison to the newer cells. I made a video recently showing how to do this upgrade that you’re talking about: https://www.youtube.com/watch?v=9KHo-T74IWA

More than likely this problem is BMS related. The BMS usually trips in that scenario for one of two reasons: 1) The load pulled by the controller is too high for that BMS, or 2) one or more cells are weak or damaged and when the load is applied strongly, it causes the voltage of that parallel group to drop below the LVC of the BMS.

trying to decide on an e-bike for a 15 mile, hilly commute. I’m a heavier rider. tested haibike with mid drive (loved it), and specialized turbo S (also loved it). It seems the mid drive does better on hills, which kill me. there also seems to be a big difference in price on the 20mph systems and the 28mph systems. for a heavier rider, is it worth the extra cash for the 28mph system?

Cool project! I’d check out electric rider (www.electricrider.com) as I know they have some good electric rickshaw and electric tricycle kits. You’re looking for a strong 48V motor that is geared really low. You want torque, not speed. With slow speed, something in the 1,000 – 1,500W is probably enough. Just don’t expect to be flying down the road…

The Stromer ST2 uses an exclusive hub motor developed by TDCM for Stromer that is being marketed as “Syno-Drive.” The Syno-Drive hub motor has a number of design changes that make it perform better, weigh less, and run smoother than any other drive system we’ve tried.

Now I’ve got all of my pack sealed in heat shrink with my wires exiting the seam between the two layers of shrink wrap. I could have stopped here, but I didn’t particularly like the way the shrink fell on the wire exit there, from a purely aesthetic standpoint. So I actually took a third piece of shrink wrap, the same size (285 mm) as that first piece and went around the long axis of the pack one more time to pull the wires down tight to the end of the pack.

Place your orders now for the new  Phoenix II http://electrichuntingbikes.com (Super Brute) Pedicab Kit, which is replacing the 4840 Brute as the new Pedicab system of choice. Some major events are coming up and there are it seems there are never enough motors to go around. The Phoenix 4840 Brute has been one of the most famous of electric pedicab kits among the pedicab industry due to its unbeatable power and reliability…..but there’s a new player in town, and it’s what we like to call the “Super Brute” motor for pedicabs It’s identical in appearance to the Phoenix Brute motors but is wound for even more torque, which is what most pedicab owners need. Installing an electric pedicab kit is a great way to seriously increase your income, especially when it comes to events like the famous Made In America Fest, Coachella, Austin City Limits Music Festival, Fun Fun Fest, Warped Tour, and the list goes on!

My thinking is that because each of the batteries is only 50% stressed, that the probability of problems due to overcurrent, etc. would be negated and I wouldn’t use a BMS for the supplementary battery.

“convert to electric bike ebike kits”

You can use any connectors you like. I’m a big fan of Anderson PowerPole connectors for the discharge leads. I used this other connector that I had in my parts bin for the discharge wires. I’m not sure what that type of connector is called, but if someone wants to let me know in the comments section then that’d be great!

Most of the price involved these days in building an e-bike or buying a ready to go e-bike is the size and chemistry  of the battery pack. For the consumer its important to understand  the difference between a 24V, 36V, and 48V pack. Also know what a 10-Ah pack is compared to a 5-Ah pack.

I then put one set of welds on each cell end of the first parallel group, effectively tacking the three nickel strips in place. Then I added another set of welds on each of the negative terminals of the second parallel group. This gave me 6 weld sets, or one weld set for each cell. Lastly, I followed up those single weld sets with another couple welds per cell to ensure good contact and connection.

The Active Line drive is designed for casual, comfortable cruising and pairs particularly well with bikes equipped with an internally geared rear hub. Featuring the full suite of sensors – including cadence, speed, and torque, the Active Line offers great hill climbing torque for moderate to steep hills. The Active Line drive offers a maximum assist speed of 20 mph.

Hi Lisa! Front hub motors can be fine, they do tend to impact steering a bit and can spin out easier but are way simpler to either install or service because they aren’t surrounded by gearing cables. The fork on most bicycles isn’t as strong as the rear dropouts (especially if there’s a suspension fork) and this is another reason why most purpose built models don’t use them. Some simple city bikes do however and you can get a good example of this with EZ Pedaler. They opted for front motors because they put geared hubs in the https://en.wikipedia.org/wiki/Electric_bikes which makes shifting at standstill possible, reduces exposure to bumps if the bike tips and is generally cleaner and less likely to need tuneups (but only offers 3 gears in this case). I hope this helps you to find the perfect ebike, feel free to post in the forums if you’d like more info or some help from fellow electric bike owners 🙂

4. How to Enter: The Sweepstakes must be entered by submitting an entry using the online form provided on this site. The entry must fulfill all sweepstakes requirements, as specified, to be eligible to win a prize. Entries that are not complete or do not adhere to the rules or specifications may be disqualified at the sole discretion of Electric Bike Technologies LLC. You may enter only once and you must fill in the information requested. You may not enter more times than indicated by using multiple e-mail addresses, identities or devices in an attempt to circumvent the rules. If you use fraudulent methods or otherwise attempt to circumvent the rules your submission may be removed from eligibility at the sole discretion of Electric Bike Technologies LLC.

Welcome to Electric Scooter Parts. We offer a large variety of scooter parts and accessories for Chinese electric scooters, electric bicycles, electric pocket bikes, electric go-karts and other small electric powered vehicles. We are continually updating our website with new parts and accessories. If there is a scooter part that you need which we currently do not have in stock please let us know and we will try to find it. At Electric Scooter Parts our mission is to offer a large selection of scooter parts in an easy to navigate and well organized store combined with excellent customer service both before and after the sale.

Your battery pack size is based on voltage and amp-hours. The higher the voltage and the higher the amp hours of your battery, the more range your battery will give you. A 48V 10-Ah pack gives you 480 watt hour (48 X 10). This gives you an easy way to determine exactly how much battery you are buying. The wattage of a battery is the only accurate determinant to judge what range your finished ebike will have.

It’s what’s inside your motor that sets it apart from the rest. Quality parts and assembly We’ve written here before about how to choose a motor, the different types of motors, the performance differences between motors, etc. But today I want to show you what makes our motors different from other hub motors. Today, harry is replacing the axle on a customer’s direct-drive motor. The bike was crashed and the…

Cell Model Samsung 2900mah. BATTERY CELL -18650 Rechargeable Lithium Battery cell. It also comes with aUSB CHARGING PORT which can be used for charging your phone. Battery Type: Dolphin Type Lithium Battery.

Wow, that’s a really interesting way to do it. So their auxiliary battery connects to the charge port of the primary battery, which means it’s not actually powering the bike but rather just charging the primary battery, which then powers the bike. Not the most efficient way to do it, but it’s simple and elegant.

Interested in becoming a Store Front Dealer X-Treme Ebike Electric Bicycle, or ElectricBicycle.com, are expanding their brick and mortar dealers Nationwide. As Bill Gates did in his infancy of Microsoft, he started in his garage. A garage business requires the founders to have enough free time to develop their idea. So if your a Store Front Dealer or a Garage Entrepreneur, we are interested in you. If you can sell 10 bikes a year and order 2 bikes on your initial order, ordering 4 bikes ships the best, please press this hyper link and complete the application and our National Dealer Manger, Jeff will call you to discuss the new business Click this Link

Shell Eco-Marathon Americas Competition 2015 1st and 2nd Place Winners Both Used an Electric Bike Technologies Hub Motor! The Mater Dei Supermileage 3 Team of Mater Dei High School, in Evansville, Ind., took the top spot in the Battery-Electric Prototype category. The team built a vehicle using an electric bike motor from Electric Bike Technologies USA and won the electric plug in class at the 2012, 2013, 2014 and 2015 Shell Eco-Marathon Americas. They…

If you are concerned about the speed and power of an electric bike, pay attention to the motor size. Electric motor size is measured in watts and usually ranges between 250 and 750. When deciding on the appropriate amount of wattage, think about factors like the weight of the rider and the desired speed and terrain for the bike. If your child will mostly be on a flat surface, lower wattage should suffice; if they are planning to ride up and down hills, look for a bike with a larger motor.

This torque arm will help prevent the motor from coming loose from the fork (front) or frame (rear) and also prevent the slotted axle from bending or breaking your dropouts. It can also be placed on the inside or outside of the frame, depending on the setup and frame of the bicycle.

“e bike crank motor -electric motor bike kit”

I just have a simple question: I would like to replace the Nicad battery 24V / 5Ah of my old Yamaha PAS XPC26 with a 7s3p and maybe try a 8s3p for something more “punchy” (hoping the controller will not burn …) . Do you think I can buy a 10s BMS and use it with a 7s or 8s battery? In this case, what should I do with the spare balance wires ?

if you carry the right tools its actually not that hard. doing it on the side of the road usually takes me about 20 minutes. it can vary from set up to set up, as you have to take apart the assembly off the bike and then pull out the tube, which can be difficult on some tires that have tough rubber treads. i would also suggest that someone care a head mount flashlight (my local dollar store sells them) as it will allow you to change them when its dark out.

Hi Peter! Yes, I’m definitely planning to review all or most of the Kalkhoff and Focus ebikes for 2016… I’m just not sure when exactly?! I’ve been kind of distracted with the site redesign and some new features but the reviews are starting to happen now! I’ll try to get a good shot of the sound for you once I have one in my hands for a test 😀

The best Electra Townie Go! design I’ve tested to date, better weight distribution, increased efficiency and greater power thanks to the Bosch Performance Cruise drive system. Available in six different colors with matching aluminum fenders, chain guard, rims and carry rack,……

3. Sweepstakes Period: Entries will be accepted online starting on or about February 1st, 2018 at 12:00 AM and ending March 31st, 2018 at 11:59 PM. All online entries must be received by March 31st, 2018 at 11:59 PM. All times are (GMT-05:00) Eastern Time (US & Canada).

Sunstar is based in Japan, and here is a PDF of their most recent mid drive motor system. Sunstar has a 2001 patent on this drive, and they are suing Bafang in Germany over the BBS01/BBS02 system that has recently become popular. That patent is 13 years old, so perhaps Bafang felt they were on safe legal ground in by copying it?

48 volt 1500 watt motor 48 volt 16.5 amp Samsun cell high quality battery 2amp charger, charges in 6 hours plus battery has USB port to charge your phone Top speed 35mph high torque Comes with every thing in the picture Motor, battery, controller and case, disc brakes and calipers, pedal assist, brake levers, tire and inner tube,LCD SW900 display, twist throttle . Let me know what size wheel you need in your order

I’m planning on building a 10S12P pack for usage on a custom DPV (Diver Propulsion Vehicle). For packaging purposes, it would be best for me to split the battery pack in several battery modules instead of a single block of cells.

Original Equipment Manufacturer Parts (OEM) have been designed by the manufacturer to be compatible with your scooter, folding bike or electric bike. That holds true for parts made by Brompton, Tern. Bulls, Stromer, Dahon  and many other brands. Find original replacement parts for the BionX electric bicycle conversion kit, like batteries, chargers, consoles, motors and wiring. NYCeWheels sells parts for Brompton Folding Bicycles whether you need to replace a part or just want to stock up with a spare, just in case. NYCeWheels even sells some hard to find replacement parts and accessories, like those for the eBike that is no longer in production.

Hi Micah, thank you for your advice. I am not going to touch that battery. I know this may be a lot to ask, but would you build me a battery for my velomini 1 ? It doesn’t have to be the one that fits in the frame, I could put it in a bag and hang it on the handlebars or something. If more convenient you can email me directly at dlimjr at yahoo. My sincere thanks and may you and your family have a happy holiday.. Don, San Francisco

Thanks so much for this excellent information. I was wondering how to calculate the total amps for the entire battery? I’m trying to determine watts from this as I have a 24V 500 watt Rayos electric bike and am working to build a 24V 20 Ah battery (7s7p) battery and would like to know what watts it is batteries electrical of providing.