“mid drive electric bike conversion kit +battery electric bike”

LiFePO4 is currently widely available for purchase as e-bike packs complete with BMS on ebay and other online merchants. Mostly it is sold by small companies. Also, most of the commercially available e-bikes powered by lithium batteries are using the LiFePO4 chemistry.

Hi Court. Thanks for your prompt response. Based on your input and further consideration I have narrowed my selection down to three Bulls e-stream brose MTB models: Evo 3 29er, Evo 3 FS 27.5 plus, and Evo 45 FS. I selected Bulls for a variety of reasons but I have to admit I am a pushover for good looks. Bulls offers a wide range of models and there is a dealer in PA within a reasonable drive from my home in MD. Unfortunately, they do not stock any MTBs but may be getting one or two in soon I can test out. I am still on the fence with regards to a full suspension bike but I realize my back is not getting any younger and I may learn to appreciate the extra comfort on the paved and unpaved hilly roads I ride. One of the suspension seat posts you suggested would definitely help with the hardtail but these are heavy and fast riding bikes (especially the EVO 45 FS which you reviewed in February) so if comfort is of prime concern a full suspension probably is the way to go.

Hub motors for bicycles are usually positioned at the middle of a wheel and when the bike is powered off they function much like a traditional hub (connecting the tire, rim and spokes to the axle. Spokes are flexible and light weight, they absorb some shock when riding but can come out of true over time. Regular bicycle maintenance is still required with an electric bike and one downside to hub motor designs is that they add additional weight to the wheel and require extra wires to deliver electricity and communications about operation. This means that truing wheels and repairing flats requires more effort.

I am working on a similar project, and was wondering if the BMS’s that you recommended would handle any back EMF from the motor (from regenerative braking, for example.) I see that there are separate leads for charging and discharging, so I’m guessing if current flowed back through the discharge circuit that would be bad. Do you have any recommendations on a BMS (or something different) that would handle this condition?

A letter from Casey Evans to Electric Bike Technologies, makers of the E-BikeKit™ electric bike conversion kit system. This one of kind adaptive electric stroller was designed by students from California State University-Sacramento using two 500w direct-drive hub motors controlled by a single E-BikeKit system. Thank you for enabling me to take my daughter hiking! My name is Casey Evans and my daughter, Montel, was born with a very rare…

Now this step is very important: I’m going to turn the pack upside-down and perform this set of welds between the positive caps on the second parallel group and negative terminals on the third parallel group. Essentially, I’m welding on the opposite side of the pack as I did when I connected the first two parallel groups. Skip down a few pictures to see the completely welded pack to understand how the alternating side system works.

Hi Frank! I used to live in San Francisco and love riding through all of those spots. Hope the city treats you well, ride safe out there. Regarding your “ideal bike” I suggest copying and pasting this question into the Help Choosing Ebikes Forum where people can share their opinions. I’d love to help but am currently traveling and trying to post new reviews with the extra time. The first thing that comes to mind is the Optibike Pioneer City which is a step-thru and uses a powerful mid-drive motor that will be excellent for climbing hills. There’s no twist throttle on this bike but the assist is very satisfying and more efficient overall. Hope this helps!

When it comes to choosing a BMS, the number of cells you have in parallel aren’t important. Only the number of series cells matters. The same BMS will work with 1 or 100 cells in parallel, as the voltage stays the same regardless of the number of parallel cells.

First of all, NCR18650B cells cannot be discharged at 2C. Those are 5A MAX cells, and really you should keep them closer to 1C to keep them cool and happy. They are economical cells. They do better when in large parallel groups so you can take advantage of their high capacity without the downside of their low discharge rate. They are great cells, but not for low AH packs.

3. Lastly, I assume if the BMS & battery were able to produce the 50A X 24V watts of 1200W that my electric motor would only ever use the 500W it is rated for? As in the E bikes controller would only draw around 500W?

A step-thru urban electric bike that hits a sweet spot between cruiser comfort and city efficiency performance, adjustable angle stem, locking suspension fork and hydraulic disc brakes. The bike comes with fenders, a sturdy oversized rack (with standard gauge pannier rods), integrated……

Wear safety goggles. Seriously. Don’t skip this one. During the process of spot welding it is not at all uncommon for sparks to fly. Skip the safety glasses and head for chemistry lab style goggles if you have them – you’ll want the wrap around protection when the sparks start bouncing. You’ve only got two eyes; protect them. I’d rather lose an arm than an eye. Oh, speaking of arms, I’d recommend long sleeves. Those sparks hurt when they come to rest on your wrists and forearms.

hello sir. nice guide FOR battery pack li-ion… i batteries for a scooter try an electric bike kit for my 26″ MTB. and buy 1000w hub motor kit. i can solve my battery problem (expensive you know) with li ion pack. i have some questions,

The battery maximum power = volts x amps, so if this 36V battery can deliver 30A continuous, that means it can deliver a maximum of 1,080 watts, though I would run it conservatively at a lower power level than that in most applications.

A new hub motor can be made for $50-$60,000 depending on what you want to do. If you simply want to make it wider you would only need to make 1 sand casting $8k-$15k. Then the stator stamp Another $12k. If you wanted to make a completely new hub motor you would need to make 3 sand castings (rotor and 2 side covers), Design and machining of the axle. The axle cost is only design and CNC time. If you were making a new Geared motor add another $15k-$20k

Next, I added the third parallel group after the second, hot gluing it in place in the same orientation as the first, so the top of the pack alternates from positive terminals to negative terminals and back to positive terminals along the first three parallel groups.

The Bionx motor system is a direct drive hub motor assembled in Aurora, Canada, outside of Toronto. Bionx is connected with Magna International, the largest car parts manufacturer in North America, and has its headquarters at Magna’s campus.

7. Winner selection and notification: Winners of the Sweepstakes will be selected in a random drawing under the supervision of the Sponsor. Winners will be notified via e-mail to the e-mail address they entered the Sweepstakes with within five (5) days following the winner selection. Electric Bike Technologies LLC shall have no liability for a winner’s failure to receive notices due to winners’ spam, junk e-mail or other security settings or for winners’ provision of incorrect or otherwise non-functioning contact information. If the selected winner cannot be contacted, is ineligible, fails to claim the prize within 15 days from the time award notification was sent, or fails to timely return a completed and executed declaration and releases as required, prize may be forfeited and an alternate winner selected. The receipt by winner of the prize offered in this Sweepstakes is conditioned upon compliance with any and all federal and state laws and regulations. ANY VIOLATION OF THESE OFFICIAL RULES BY ANY WINNER (AT SPONSOR’S SOLE DISCRETION) WILL RESULT IN SUCH WINNER’S DISQUALIFICATION AS WINNER OF THE SWEEPSTAKES AND ALL PRIVILEGES AS WINNER WILL BE IMMEDIATELY TERMINATED.

You may have missed the point – I’m considering both front and rear motors together – 1,000W DD in the back (I figure there will be less wear and tear given the action in the looses sand) and a 350W geared motor in the front. They would be on separate throttles and the front motor would only be used very occasionally – if and when the back wheel really digs in. The rider’s pedaling is by way of assistance to the rear motor.My reluctance to deploy a BBS02 is based on:

Love your youtube videos! I’m actually looking to make an electric longboard on the cheap. I have an 18V motor (from a battery drill) that I want to power and I have purchased 10 (AA) 3.6V 3000mAH Lithium-ion batteries with the intention of connecting them together in a series arrangement to run the motor. What would be the best way to arrange them? And is there a need for a BMS for a smaller arrangement? Or would it be more time effective/safer to just charge each battery individually? Any help is appreciated.

The @blixbike Vika Travel is the perfect #multimodal companion. Few #ebikes get this small and ride this well! #blixbike #electricbike #ebike #foldingbike #electricfoldingbike #nycewheels 07.03.2018 – 02:51

The Dapu geared hub motor is made by a Japanese company in Shanghai, China. The Dapu motor is a geared hub motor. This motor type is distinct from a direct drive motor like Bionx, and has a variety of benefits stemming from its design that can be appreciated in its unique ride feel and performance. Geared hub motors work by transmitting power from a high RPM motor to the slower RPM wheel through a system of planetary gears. Because of the physics of electric motors, this “gearing” allows for higher torque and efficiency from the motor. Thus, the ride feel of a BH Neo bike is extremely sporty with consistent torque, even up

Hi, Court Rye! Thank you for your response . As I supposedly said, I do cca.20 km per day. 2000 – 3000 per year. The main road is straight, as well as highs. Just for them I need help of the engine. I send you pictures of the engine that are offered to me . They said that discourage hub motor ( in the first wheel ) , as well as the Mid – Bafang , because often corrupts !? So, what do you mean? Thanks and best regards, Miran

Weight for weight, nickel-cadmium (NiCd) batteries have more capacity than lead-acid battery, and capacity is an important consideration on an electric bike. However, nickel- cadmium is expensive and cadmium is a nasty pollutant and hard to recycle. On the other hand, NiCd batteries will last longer than lead-acid batteries. But the reality is that because they are so hard to recycle or get rid of safely, NiCd batteries are rapidly becoming a thing of the past. These are also not a good choice of battery type, regardless of price.

Leave a Reply

Your email address will not be published. Required fields are marked *