“lithium bike battery _motorized bicycle electric”

Most electric bicycle batteries fall into the 24V to 48V range, usually in 12V increments. Some people use batteries as high as 100 volts, but we’re going to stick to a medium sized 36V battery today. Of course the same principles apply for any voltage battery, so you can just scale up the battery I show you here today and build your own 48V, 60V or even higher voltage battery.

Thank you very much for quick answer. You give me a good advice and I will use it. To sum up, now I am on the cross Li-ion or LiFePO4, can you sugest me some othre examples like Panasonic 18650 which you tested and you clame are good batterys? For BMS, is there special tipe which are good or there is no different or just like you says it must be for a bit stronger etc. batterys give 30A we must have a bit stronger BMS like for 40A?

If I regroup my 12 paralled cells in 10 modules, can I then join these in series using single wires (one for neg, one for pos) between modules, instead of wiring each terminals of each cells like you are doing. Could this affect BMS and/or have any negative impact on cells balance?

How do you determine this exactly? Your battery is a 36v 8.7Ah and I guess it has something to do with the maximum continuous discharge rate. It would help me (and maybe others) to explain why 30A is more than enough for this battery.

Yes, that’d work, but I’d get an additional 7s battery so you have 20s total. Also, you should know that the older your original 48V battery is, the more time it will take your new 72V combined battery to balance, as the first 13 cells will likely have less capacity in comparison to the newer cells. I made a video recently showing how to do this upgrade that you’re talking about: https://www.youtube.com/watch?v=9KHo-T74IWA

More than likely this problem is BMS related. The BMS usually trips in that scenario for one of two reasons: 1) The load pulled by the controller is too high for that BMS, or 2) one or more cells are weak or damaged and when the load is applied strongly, it causes the voltage of that parallel group to drop below the LVC of the BMS.

trying to decide on an e-bike for a 15 mile, hilly commute. I’m a heavier rider. tested haibike with mid drive (loved it), and specialized turbo S (also loved it). It seems the mid drive does better on hills, which kill me. there also seems to be a big difference in price on the 20mph systems and the 28mph systems. for a heavier rider, is it worth the extra cash for the 28mph system?

Cool project! I’d check out electric rider (www.electricrider.com) as I know they have some good electric rickshaw and electric tricycle kits. You’re looking for a strong 48V motor that is geared really low. You want torque, not speed. With slow speed, something in the 1,000 – 1,500W is probably enough. Just don’t expect to be flying down the road…

The Stromer ST2 uses an exclusive hub motor developed by TDCM for Stromer that is being marketed as “Syno-Drive.” The Syno-Drive hub motor has a number of design changes that make it perform better, weigh less, and run smoother than any other drive system we’ve tried.

Now I’ve got all of my pack sealed in heat shrink with my wires exiting the seam between the two layers of shrink wrap. I could have stopped here, but I didn’t particularly like the way the shrink fell on the wire exit there, from a purely aesthetic standpoint. So I actually took a third piece of shrink wrap, the same size (285 mm) as that first piece and went around the long axis of the pack one more time to pull the wires down tight to the end of the pack.

Place your orders now for the new  Phoenix II http://electrichuntingbikes.com (Super Brute) Pedicab Kit, which is replacing the 4840 Brute as the new Pedicab system of choice. Some major events are coming up and there are it seems there are never enough motors to go around. The Phoenix 4840 Brute has been one of the most famous of electric pedicab kits among the pedicab industry due to its unbeatable power and reliability…..but there’s a new player in town, and it’s what we like to call the “Super Brute” motor for pedicabs It’s identical in appearance to the Phoenix Brute motors but is wound for even more torque, which is what most pedicab owners need. Installing an electric pedicab kit is a great way to seriously increase your income, especially when it comes to events like the famous Made In America Fest, Coachella, Austin City Limits Music Festival, Fun Fun Fest, Warped Tour, and the list goes on!

My thinking is that because each of the batteries is only 50% stressed, that the probability of problems due to overcurrent, etc. would be negated and I wouldn’t use a BMS for the supplementary battery.

Leave a Reply

Your email address will not be published. Required fields are marked *