“electric mountain bike motor |electric bicycle frame”

Hello Court! I have spent a good deal of time the past few months researching e-bikes. I read your introductory book and nearly every online review you have written over the last year or so. The closest e-bike shops to me are about a two hour drive and are limited in what brands and models they stock (mainly city style bikes). So before I venture out to test drive a few models, I am seeking your advice to narrow down the type of bike and drive train that makes the most sense for my application.

When it comes to choosing a BMS, the number of cells you have in parallel aren’t important. Only the number of series cells matters. The same BMS will work with 1 or 100 cells in parallel, as the voltage stays the same regardless of the number of parallel cells.

Hi Lalith, cool name you have! If you are buying a high volume of electric bike motors and batteries, then you could probably buy direct from China and maybe use a website like Alibaba. However, if you need a small or medium number, maybe you could research a company like Clean Republic. I reviewed their affordable Hill Topper kit a while back and thought it was good. If you are buying for Africa, it might be easiest to source parts in Africa or find a wholesaler in China that can ship there vs. going from China to the US and then Africa. I hope this helps you! Be careful if you are planning to buy and then fly with products like this because high capacity Lithium-ion batteries are not usually allowed.

The Xion motor is a new drive system available on Focus and Kalkhoff electric bicycles. The drive was developed in cooperation between Derby Cycles, the parent company of Focus and Kalkhoff, and Alder, a German-based wheelchair motor manufacturer. The Xion drive is a traditional, reliable direct drive hub motor with a twist: it uses a sophisticated optical sensor to precisely determine the position of the copper windings relative to the magnets and apply power in exactly the right place at exactly the right time. This allows the Xion drive to work

i am building a 10s4p 36v 18650 battery pack for my ebike, what gauge silicon wire you recommend for discharge and charge wires, i am using 2.5 amp 42.5v li-ion battery charger bought from ebay(http://www.ebay.com/itm/281639749374?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT), and 10s 36v 30amp bms bought from ebay(http://www.ebay.com/itm/182247900118?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and 500w 36v controller.

You told us what you wanted and now we’re delivering it. ShippingPass is our new subscription program designed to bring you unlimited 2-day free shipping for batteries for electric scooters canada year with no minimum order. Get what you need ― fast!

An electric bike kit allows the do-it-yourselfer to transform just about any standard pedal-powered bicycle into an electric-powered vehicle. Monster Scooter Parts offers several high-quality electric bike conversion kit models suitable for the traditional bike rider with no more than a scant-to-average mechanical ability. Our e-bike kit models listed below are some of the best known in today’s e-bike community.

Why does this formula work? Think about it: heat shrink (unless stated otherwise) usually has a 2:1 shrink ratio, so if I need something with less than twice the circumference (or perimeter rather, since my pack isn’t really a circle) of my pack. Since large diameter heat shrink is quoted in half circumference (flat width) sizes, and I want heat shrink with a circumference of a bit more than the perimeter of my pack, then I know I need the half circumference size to be a bit more than half of my pack’s perimeter, which is equal to the height plus the width of my pack.

If any one battery cell varies significantly from the others, do NOT connect it to the other cells. Paralleling two or more cells of different voltages will cause an instantaneous and massive current flow in the direction of the lower voltage cell(s). This can damage the cells and even result in fire on rare occasions. Either individually charge or discharge the cell to match the others, or more likely, just don’t use it in your pack at all. The reason for the voltage difference could have something to do with an issue in the cell, and you don’t want a bad cell in your pack.

Hi Ben! I had an opportunity to test ride an old Lee Iacocca eBike a while back and was impressed with how forward thinking the design was. I can see why you’re excited about the space, especially with all of the new products coming out, and given your lack of a driver’s license.

So after buying a 48v 20 Amp battery from Ebay (and knowing very little at that point), I realized it didn’t have a BMS and heard rumors that if i attached it direct to the controller, it would see it as a short (controller would be closed) and blow the controller.

One Reply to ““electric mountain bike motor |electric bicycle frame””

  1. Offset packing results in a shorter pack because the parallel groups are offset by half a cell, taking up part of the space between the cells of the previous parallel group. However, this results in a somewhat wider pack as the offset parallel groups extend to each side by a quarter of a cell more than they would have in linear packing. Offset packing is handy for times where you need to fit the pack into a shorter area (such as the frame triangle) and don’t care about the width penalty.

Leave a Reply

Your email address will not be published. Required fields are marked *