“electric bike battery ebike bms”

As much as I want to build a pack just for fun and like buying tools like a spot welder I’m afraid of getting crappy cells at a high price. Whatj’s a good cell to charge at 1C for quick turn around and stay at a low price per cell? 36V 12A would be ok, more is a bonus.

A lithium battery is the heart of any electric bicycle. Your motor is useless without all of that energy stored in your battery. Unfortunately though, a good ebike battery is often the hardest part to come by – and the most expensive. With a limited number of electric bicycle battery suppliers and a myriad of different factors including size, weight, capacity, voltage, and discharge rates, finding the exact battery you are looking for can be challenging and lead to unwanted compromises.

Gotcha. Can you recommend a manufacturer that sells a two wire version? Maybe I can look around their products and see if they sell any 7S cells, rather than sifting through all the manufacturers on Alibaba. Searches for “2 wire MBS” didn’t yield much. Thanks again for your help with this!

To wire the BMS, we first need to determine which of the sense wires (the many thin wires) is the first one (destined for the first parallel group). Look for the wires to be numbered on one side the board. Mine is on the backside of the board and I forgot to take a picture of it before installing it, but trust me that I took note of which end the sense wires start on. You don’t want to make a mistake and connect the sense wires starting in the wrong direction.

I am looking to purchase my first electric bike. I have test ridden many and narrowed my favorites to the eMotion City Wave and the Pedego City Commuter, with 28″ wheels. I don’t anticipate lengthy trips – likely up to 30-40 miles tops, however we live in the hills of NH, so I would be using pedal assist and/or throttle for the tougher climbs. While I love the City Wave ride, I worry a bit about the 350W vs. the possible 500W on the Pedego. I am 5’8″ and weigh 138 lbs. Your thoughts?

I have been looking up materials and researching where to buy them for my battery pack. I’ve come to the exact conclusions (and almost the exact same materials) that you write about in this great article. Too bad i didn’t find it earlier… Doh!

I also soldered rather than spot welded and used 1.5mm2 solid core copper between cells, pre-bent to zig-zag shapes on a jig (current is then distributed between them). Offtakes were 4mm2. Soldering technique to minimise heat on the cells was to paint the cells and the wire with flux, load the soldering iron tip with enough solder to make the joint and then, while holding the wire on with the back of a wooden pencil, touch the molten solder to the cell/wire interface and immediately remove the soldering iron tip. This worked really well in terms of soldering quality and the solder cooled very quickly indeed. I cleaned the flux off with a baby wipe and then dried it with some paper kitchen towel.

An affordable full suspension trail bike with quiet, but powerful, mid-drive motor and integrated downtube battery pack, full-sized USB charging port on battery, adjustable top speed. Integrated LED headlight, backlit LCD display panel, and standard reflectors for urban riding, high-pressure tires……

I guess I’ll just have to risk some deterioration on the cells. I don’t think there’s much of an effect, as I did it on an old 18650 cell to test. The joint and surrounding areas were cool to the touch within 1-2s of removing the heat.

I have a homemade battery made up of 84 NCR18650b cells that I bought (in other words, I didn’t make the battery myself). Anyway, I lost the charger for it at Burning Man, and now I’m going nuts trying to figure out what kind of charger to buy. The arrangement of the batteries is odd. Part of the battery looks pretty straight forward in what I believe is a 8s6p design, but the rest look different… they are set up like a 4×3 rectangle framed by 2 L’s. I would have happily uploaded a picture, but that doesn’t seem possible. Is there anyway I can send you a picture to show you what I mean?

Hi Len, I think I understand and was recommending against the added weight and complexity of two motors. It has been done (Easy Motion sells a couple of all-wheel-drive ebikes) but wiring both motors into a single battery could be tricky and the alternative of having two batteries would take up a lot of space and add weight. In terms of torque from mid-drive vs. rear hub, I think it depends on the system you go with, both can be powerful and effective… You made a good point about the chain and rust. I don’t have enough data to recommend one way over the other, both have pros and cons… I might go with the cheaper option since it sounds like the bike is going to get run down in the environment so replacement will be less expensive down the road.

Mike is a partner and adviser to Electric Bike Technologies. Mike has been a professional investor and salesperson in the financial sector for the past 20 years. “It’s a great space to be in and and I believe there is a lot of upside potential”

Get the most out of your electric bike, folding bike or scooter with batteries for electric scooters canada parts and accessories available at NYCeWheels. Whether you are looking to add on to and upgrade your bike to make it more fun, efficient or stylish, or you simply need to replace a part, NYCeWheels has a large inventory to assist you.

Offset packing results in a shorter pack because the parallel groups are offset by half a cell, taking up part of the space between the cells of the previous parallel group. However, this results in a somewhat wider pack as the offset parallel groups extend to each side by a quarter of a cell more than they would have in linear packing. Offset packing is handy for times where you need to fit the pack into a shorter area (such as the frame triangle) and don’t care about the width penalty.

The #kleeferpure180 is the best multimodal commuter scooter with the fastest fold! Trolley it easily and pop it open when you’re ready to ride! #kickscooter #scooter #scootcommute #multimodal #nycewheels 22.02.2018 – 23:27

The stokemonkey is only for long cargobikes like the Yuba Mundo, Xtracycle Edgerunner, and Surly Big Dummy, but…if you actually haul cargo, this drive absolutely conquers hills when you are fully loaded. They are still available in the classic edition (where the pedals turn when the motor is running) but now…they also have a freewheeling crank option. This system has recently been upgraded, and is now sold by ebikes.ca

However… I’m thinking about extending the range of my 250W ebike (a Greenedge CS2) by wiring a battery in parallel as a one-off project. My thinking is that as it would halve the load on each of the batteries, it would reduce output current and voltage drop under load. This I’m thinking would allow use of a simpler constructions, since the stress on each cell would be reduced.

One Reply to ““electric bike battery ebike bms””

  1. Hi Court and thanks for all the info. I am in Montréal and would like to know in minus 15 and minus 25 what range may i expect? I am 160 pounds and would pedal, mostly flat and asphalt with 1/3 old railroad now small gravel. I am looking at a Surface604 Element 60 pounds 3 assist levels plus throttle. Weekly i go to a secondairy house 65 km away wich i pedal in 2.75 hours on my 18 pounds summer road bike.

Leave a Reply

Your email address will not be published. Required fields are marked *