“e bike motor +electric mountain bike motor”

Hi Craig, the ST2 is an awesome ride with some really neat features. I wouldn’t feel comfortable recommending it over another model until I knew your height, weight, desired distance and terrain (off-road, packed trails or mostly street). I personally have some neck and back issues so I like the full suspension ebikes with large knobby tires for a bit of trail riding. I’m not a large rider so I prefer my frame size to not be too large or heavy and I don’t want to go over 20 mph so that helps me focus on a specific group of bikes… If you share your details maybe I can make some more informed recommendations here.

You mentioned that you made a discharger from halogens. Is there any reason not to just use a couple power resistors in parallel, like 2×25 ohm, 100w for a 13s6p pack? Do you know why it’s helpful to take it easy on the pack for the first couple cycles?

The UpCycle Eco-Charger is a Powerful Bicycle Generator that Utilizes an E-BikeKit™ Hub Motor and Empowers You to Generate Your Own Electricity!   The UpCycle Eco-Charger was created by Adam Boesel, the founder of The Green Microgym Say goodbye to worrying about environmental disasters and hello to making the world a better place. The UpCycle Eco-Charger is the most efficient, reliable, and powerful bicycle generator ever. Over the past two…

Either way works, but my orange jig saves me one hot glue step which just makes for a cleaner looking pack. Of course it’s all the same after the pack gets covered with shrink wrap, so you can use any method you’d like. I’ve even found that some of those cylindrical ice cube trays are perfectly sized to hold 18650 cells. Cutting off the top would leave it clear for welding. I’d add some strong neodymium magnets to the backside to hold the cells in place like my orange jig has, but other than that it’s a perfect jig almost as-is.

Hi Jasmine! Interesting question, I think you could use a geared hub motor mounted in a 20″ wheel but am not sure if that would match your wheelchair perfectly or mount to a side axle vs. one that’s built into the hub (most ebike hub motors I’ve seen are permanently fixed to the axle). Lots of companies offer basic motor, battery, controller kits but this one from Dillenger appears to come in the small 20″ wheel size. Maybe there’s a way to add a mounting system between the two rear wheels to have this third wheel act as power? The other challenge is reverse, most electric bikes don’t offer this but one company called E-BikeKit does with their trike conversion kit here which may also come in 20″ wheel size. I hope this helps you get started, if you call the E-BikeKit company ask for Jason and maybe he can even give you some more advice as they offer some models designed to be more like personal mobility trikes vs. fast commuter bikes. One such model is their Liberty Trike here.

This article first appeared in Electric Bike Report in June of 2013. Since then, we’ve made some changes to our motor selection – our Direct-Drive motors are now all High-Torque 6×9 wound, so they run slower (approximately 15mph at 36v or 20mph at 48v), and our Geared Motors have been replaced by a 500w version, (approximately 20mph at 36v or 28mph at 48v). The Direct-Drive is now our Heavy-Duty motor and the…

Bafang (8Fun) is a Chinese manufacturer of electric bike motors. Bafang is one of the world’s largest producers of motor systems, primarily front hub geared motors for the European market (primarily the Netherlands). Besides front hub motors, Bafang also produces a range of rear hub drives, a simple mid-drive motor, and ebike components such as consoles (HMIs) and battery packs.

Four hundredths of a volt is probably fine to parallel them, but I would be more worried about why the cells aren’t all the same. If they are brand new cells from the factory, they should be nearly spot on. These might be more expensive than what you paid, but I get my Samsung 25R cells from this vendor, where I know they’re genuine and straight from the factory, and all come at exactly the same voltage.

The last step of wiring the BMS is to add the charge and discharge wires. The pack’s positive charge wire and discharge wire will both be soldered directly to the positive terminal of the 10th parallel group. The negative charge wire will be soldered to the C- pad on the BMS and the negative discharge wire will be soldered to the P- pad on the BMS. I also need to add one wire from the negative terminal of the first parallel group to the B- pad on the BMS.

As of August 1st, 2015, every E-BikeKit and E-TrikeKit will now include a set (8 x guides and 14 x zip ties) of Flexroute Guides and Cobra zip ties. These items are being added at no additional charge. Packs of these guides and specialty zips are also available for sale in our online shop.

Electric bikes are a reliable source of transportation. With a new battery from Batteries Plus Bulbs, you can expect the same level of reliability. Our high capacity, replacement batteries will get your scooter moving again and keep it running for a long time.

ElectricRider still has a few 4840 Phoenix Cruiser kits, 1000W Bafang kits, RoadRunner II Motors, and a lot of parts. If you need help placing an order or have any questions, please send an email to [email protected]

I am just trying to install a battery on a velomini 1 that I traded for. I don’t have a problem using the above battery as a hang on battery, but don’t know if it has the BMS in it or if my current charger would charge it. It is pretty cheap.

Hi I need help! I am building my own battery pack from old laptop batteries (18650’s). I bought the cheep $250 48v 1000w ebike conversion kit on ebay. I have many questions! It seems the perfect number of cells to connect in series are 13! This is a big problem for me because I am cheep and I already bought the Imax B6 battery balancer charger. I also bought 7x 6s balancer leads and 5x 4s leads. The Imax has a max charge voltage of 22.2v (so it sais in the manual), and a max balance of 6 cells at once. I also bought the parallel balance charging board. I don’t want to charge two or three packs at once to just have to turn around and charge one separately. So now I’m faced with the decision of making a 12 series battery or a 15 series battery (I will buy 5s leads in this case). The problem is with the 12 series battery the nominal voltage is only 43.2. Or a 15 series battery with a nominal voltage of 54. Which I’m pretty sure is a big no no because the controller is only meant to handle 48v within reason (13s max charge voltage of 53.3 and 12s 49.2 at 4.1 v per cell). But if I make it a 12s, running around most of the trip at 44v, will this drain the Amps faster because the motor wants 48v? I’m thinking no but just wanted some confirmation on that and if the controller can handle more volts. I could make a 15 series batter and just charge to 3.6 or 3.7 volts. Is this hard on the cells?

You can use any connectors you like. I’m a big fan of Anderson PowerPole connectors for the discharge leads. I used this other connector that I had in my parts bin for the discharge wires. I’m not sure what that type of connector is called, but if someone wants to let me know in the comments section then that’d be great!

Power: 500W / 36V. Allow you to swap two power modes between the full 500W power to 750W power by a single blue switch wire is embedded in controller. (Only for Twist Throttle). Still remain the full 500W power with no speed control.

Dennis bought a 2017 M-850 Addmotor MOTAN Electric Bicycles Sport Orange Super Discount For Sale 500W 48V Bafang Rear Hub Motor 10.4AH Samsung Cell Battery Pack Electric Bike For Big Guys With Fork Suspension And Spring Shock Absorber

Hi Sundaram, I’m not aware of many 18650 LiFePO4 cells, are you sure you are using that chemistry instead of standard lithium ion? Perhaps can you provide a little more detail about the specific cells you’re using?

Hey Brian, good question. You can actually do regenerative braking this way, the only problem is that you won’t be using the balancing circuit part of the BMS as it will charge straight back through the discharge circuit. Theoretically this is fine, with the exception of one specific case where this could be a problem. If you charged your battery at the top of a huge hill and then immediately rolled down that hill for a long time while using regenerative braking, you could actually overcharge the battery. That scenario is pretty rare though.

This kit has also been run at 72V X 30A = 2,200W/3-HP (with a different controller), but be aware that this level of power requires a swap to a chain primary reduction, or a wider belt. Also, the GNG allows for a stronger crankset to be swapped-in for riders who like radical jumps without bending the spindle (the BBS02 crankset cannot be upgraded).

Hi Micah, thank you for your advice. I am https://en.wikipedia.org/wiki/Electric_bikes going to touch that battery. I know this may be a lot to ask, but would you build me a battery for my velomini 1 ? It doesn’t have to be the one that fits in the frame, I could put it in a bag and hang it on the handlebars or something. If more convenient you can email me directly at dlimjr at yahoo. My sincere thanks and may you and your family have a happy holiday.. Don, San Francisco

This electric motor has the more acceleration at low end, better mid range, and more top end. It’s easy to fix disk on front & rear hub motors.This e bike motor will go nearly 600RPM on 48V, also offer this wheel professionally laced into leaf double wall aluminum rims with 12g spokes. Message us for details. 20″, 24″, 26″, 27.5″(650B), 700c , 28″, 29″  sizes are available.

A step-thru urban electric bike that hits a sweet spot between cruiser comfort and city efficiency performance, adjustable angle stem, locking suspension fork and hydraulic disc brakes. The bike comes with fenders, a sturdy oversized rack (with standard gauge pannier rods), integrated……

The Panasonic mid-drive motor is a remarkable bit of engineering. The basic motor design has stayed the same since the early 90s, when Yamaha and Panasonic began building drive systems for pedal assist electric bicycles. What has changed dramatically is the battery technology, which has allowed the Panasonic drive, which since the beginning was extremely reliable, to get better and better, offering riders more power and better range per charge. Today Panasonic remains a top-tier electric bicycle drive manufacturer being spec’d on a wide range of bikes from companies such as Kalkhoff, Focus, Raleigh, KTM, Helkama, and BH Easy Emotion.

A highly adjustable, feature-complete, city style electric bike with long fenders that have an integrated headlight and enclosed chain cover keep you clean and dry, integrated keyed-alike cafe lock adds convenience. Available in three frame sizes with the small and medium being wave and the large……

I am currently building my own 36v battery and now using some of the ideas you have put here. but I am wondering what is going to be the best charger for charging the battery?? As I am doing on the cheap, I am utilising a 12v 6A charger which I previously had. My plan was to couple with a 12v to 36v step up DC transformer but then realised that this may not be enough to charge the battery fully. This is because the full charge voltage on the battery is actually 41v which would be higher than the step up transformer. The next option is a 48v charger which would be too high.. Or would the BMS kick in and protect from over voltage?? This is all theory at the moment so I am probably missing something.. Could you suggest a charger method. Am I on the right track?

hi, recently, i try the BOSM intelligent torque sensor. its a miracle. It makes your ebike become a real ebike, like a human, it know your idea,you wanna fast,slow,climb mountain, across the grass , against the wind etc. It will adjust the output power intelligently.

Next, I added the third parallel group after the second, hot gluing it in place in the same orientation as the first, so the top of the pack alternates from positive terminals to negative terminals and back to positive terminals along the first three parallel groups.

Please see the video’s on RCgroups under LiPo fires. A simple 2200maH 3S battery pack blew the lid off a secured 55caliber ammunition can. Putting a LiPo pack in a closed metal case is a real “bomb” waiting to happen. See all the videos on RCgroups that show what happens when a battery is over-charged or over-discharged inside air-tight causes. The real solution is to make the case have a “preferred direction” of discharge……which can be very powerful. This is done by drilling holes in the case. But it stops the explosion factor. The best thing is to have a BMS on or inside the battery. Even if the cheapy Hobby King voltage monitor, that is much better than nothing at all. Also consider putting in a voltage monitor that has a temperature guage attached. When ever the pack skin gets above 85 deg C, you are in real danger of “vent and flames”. The temperature and voltage are that two big things that can make your battery pack safe………….also store the pack where if it does go to “vent and flames”, no human being will get burned.

Next, plan out your cell configuration on your computer or even with a pencil and paper. This will help ensure you are laying out your pack correctly and show you the final dimensions of the pack. In my top-down drawing below I’ve designated the positive end of the cells in red and the negative end of the cells in white.

NYCEWheels has some of the best bike accessories you’ll find anywhere, whether you’re looking for accessories for electric bikes or for standard bikes. Our accessories can improve your safety,… read more »

Leave a Reply

Your email address will not be published. Required fields are marked *