“e-bike controller -convert electric bike”

The last step of wiring the BMS is to add the charge and discharge wires. The pack’s positive charge wire and discharge wire will both be soldered directly to the positive terminal of the 10th parallel group. The negative charge wire will be soldered to the C- pad on the BMS and the negative discharge wire will be soldered to the P- pad on the BMS. I also need to add one wire from the negative terminal of the first parallel group to the B- pad on the BMS.

In some cases a front mounted hub motor is preferred because it allows an internally geared hub or continuously variable transmission CVT hub such as the NuVinci to be used in the rear. Some of the newest electric bikes like the Smart ebike combine an internally geared hub (that the cyclist pedals) with a hub motor and are able to put both in the rear wheel.

Bionx is the perfect system for http://twowheelev.com to steep hill climbing and instant acceleration. Bionx’s regenerative mode is unique in both its efficiency (up to 15%) and its usefulness—it will automatically slow your bike down when the brake is applied lightly, saving your brake pads and extending riding range per battery charge. Finally, the direct drive motor design allows for extremely reliable performance—the two bearings in the motor are the only wear points—and completely silent operation.

Thanks for the article, Court. I’m researching so much it feels like a part time job! I have a morning newspaper route that is about 22-25 miles and I would like to start using an ebike for the delivery, as weather permits. According to your article, I’m not going to be able to escape a compromise on some level. If I understand correctly, the constant starting, stopping, and slow speed adjustments could be taxing and uncomfortable with a geared hub. I’ll post my unique situation in the forum instead of hijacking this space.

As the e-bike concept grows in global aceptance, the electric bike conversion kit makes more sense for a variety of reasons. The hard-core bicycle enthusianst will appreciate the flexability of upgrading their favorite ride with an e-bike kit, while e-bike neophyte can experience personal electric transportation for a relatively modest up front outlay.

Now this step is very important: I’m going to turn the pack upside-down and perform this set of welds between the positive caps on the second parallel group and negative terminals on the third parallel group. Essentially, I’m welding on the opposite side of the pack as I did when I connected the first two parallel groups. Skip down a few pictures to see the completely welded pack to understand how the alternating side system works.

“Great company!!!! Unbelievable shipping!! Ordered Item on a Monday received it on a Thursday. I had a question about installing the part, called and the customer service representative walked me through it. Very knowledgeable, I will definitely buy from again.” – Debra from Tallahassee, FL

“Greetings, thought you may like to see an article about a scooter made using parts supplied by your company. It won first place in an engineering competition. Thanks for your help, and the fast delivery of the great parts!” – Dan from Tracy, CA

A value-priced urban electric bike that includes fenders, integrated LED lights, a rear rack, and hydraulic disc brakes, it’s available in three frame sizes but only high-step. This is a high-speed Class 3 ebike that can reach ~28 mph assisted and because……

I think it is much better to use a purpose built CV-CC (constant voltage, constant current) ebike charger. I 100% understand the desire to complete the project on the cheap, but I think that sometimes it is worth a few extra bucks as insurance to protect your battery which is worth many hundreds of dollars.

Hi Pâmini! Yes, I’ve definitely been planning to review the Spicy Curry and I agree with you that the smaller 20″ rear wheel helps to improve balance. It also improves power because less torque is required to turn a smaller wheel. For the price, it seems like one of the best options. You can see my thoughts on the TranzX mid-drive motor by watching this review of the IZIP E3 Peak which uses the same setup. I admit that I do not like this drive system quite as much as Bosch but it is getting better and for the price it is quite good. I hope you and your girls have a blast riding whatever bike you choose and maybe in time you can let one of them tag along with a trailer like this that teaches riding. Also, here’s a video I made a while back that teaches the balance for riding a bike on your own 🙂

You don’t know Ecospeed. If you did, and if you tested, you would realize that Ecospeed should be rated as the number one mid drive system out there. Based on years in business, satisfied customers, technology, engineering, and service. I know, since I have had Ecospeed for 5 years or more and I have two of the latest iterations of Ecospeed (one mtn bike and one recumbent) and use it to climb 2500 vertical feet of logging roads regularly. And it is fantastic.

– BMS/Greenbikekit are now selling cased or shrinkwrap LiFePo batteries based on high capacity cylindrical cells probably from Headway and with a BMS. These have a higher C Rating between 5C and 10C. This makes a 48v-10AHr battery useable in a high performance kit with 30-40A max. Using this with a 1000W-1500W motor/controller should work fine. This is heavier than LiPo but close to the holy grail. Long lasting, safe/easy/convenient, high power.

Torque arms are to provide reinforcement for your bicycle frame, when using an electric hub motor. They are a MUST for almost any electric bicycle conversion, but especially for front or rear applications.

I like to cut most of my nickel strip in advance so I can just weld straight through without breaking my flow to stop and cut more nickel. I measured out the width of three cells and cut enough nickel strip to weld the top and bottoms of 10 sets of 3 cells, meaning 20 strips of nickel that were each 3 cells wide, plus a couple spares in case I messed anything up.

If you don’t have an actual heat gun, you can use a strong hair dryer. Not all hair dryers will work, but my wife’s 2000 watt model is great. I own a real heat gun but actually prefer to use her hair dryer because it has finer controls and a wider output.  Just don’t go mess up your wife’s hair dryer!

BikeBerry.com is the world leading bicycle and motorized bicycle accessories suppliers. You’ll find the guaranteed lowest prices on motorized bicycles, bicycle engine kits, mopeds, scooters and unicycles.

So to recap… hub motors operate independently of the rider pedaling, they can be geared or gearless, can fit in the rear wheel, front wheel or even independently from the wheels as with the Organic Transit ELF (though this is very uncommon) and they can sometimes generate electricity. Some drawbacks of all hub motors include increased unsprung weight, which can reduce traction, limit efficiency and strain spokes and rims. They usually have just one gear setting that can operate at a faster or slower speed but cannot shift for improved torque or speed. They also tend to make wheels more difficult to service (changing flat tires or fixing spokes) because they add weight to the wheel and require extra cables to deliver electricity and operation signals (unless they are an all in one hub motor like the FlyKly or Copenhagen Wheel).

If you don’t find that, there’s still a chance that it’s the problem, and that the cells simply rose up to a higher voltage and matched the others again once the load disappeared. But it also may be that the load is too high for the BMS. Do you have a cycle analyst? You could slowly increase the throttle and watch how much current you are drawing until the point of cutoff. If it’s well below 40A then you’ll know it’s not a high current cutoff.

The Cyclone system is the first electric bike motor kit to work with the bike’s rear deraileur to take full advantage of your bike’s gearing system. The kit can be installed on bikes with 6 to 8 speed rear cassettes. The result is a motorized bike with great low gear power and a comfortable high-end cruising speed.

Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[65]

An electric bike kit allows the do-it-yourselfer to transform just about any standard pedal-powered bicycle into an electric-powered vehicle. Monster Scooter Parts offers several high-quality electric bike conversion kit models suitable for the traditional bike rider with no more than a scant-to-average mechanical ability. Our e-bike kit models listed below are some of the best known in today’s e-bike community.

One Reply to ““e-bike controller -convert electric bike””

  1. 18650 cells, which are used in many different consumer electronics from laptops to power tools, are one of the most common battery cells employed in electric bicycle battery packs. For many years there were only mediocre 18650 cells available, but the demand by power tool makers and even some electric vehicle manufacturers for strong, high quality cells has led to the development of a number of great 18650 options in the last few years.
    I understand that the Ebay battery may run low, but as it is running in parallel to the “Whale”, I’ simply use the “Whale” LED display as rough guid to both batteries charge state (assuming I fully charge both batteries each time before I ride).
    Although the motor is the same, every part of this drive is very strong and uses the highest quality components, including a 25mm wide primary reduction belt, instead of the GNG’s 15mm wide, and…a #219 kart chain for the secondary, which is rated for over 20-HP (15,000W). By moving the motor-freewheel from the right side, over to the large primary driven pulley on the left, the reduction has been improved to 33:1 (compared to the original GNG reduction of only 21:1).
    Lithium chemistry is considerably more expensive than the “old school” lead acid chemistry. If you are buying a battery pack or a bike that already has a battery pack, be familiar with the chemistry that you’re buying. For example, its hard to find a good e-bike for under a thousand dollars with a decent-sized lithium pack. Lithium is pricey. Be realistic in your expectations when e-bike shopping on how much the electric bike will cost compared to what kind of range, performance, and life expectancy you will get out of a lithium battery pack.
    Fat E-Trike from Sun and E-BikeKit™ at Interbike 2014 Fat bikes and electric bikes were all the rage this year at interbike in Las Vegas. It seemed almost every bike vendor at the show has at least one fat bike model in their booth this year. On top of the fats were the electric bikes. And I think it goes without saying that nobody wants to actually pedal a fat…

Leave a Reply

Your email address will not be published. Required fields are marked *