The purchase price is often a turnoff for many people, but in reality $200 for a good hobby-level spot welder isn’t bad. All together, the supplies for my first battery, including the cost of the tools like the spot welder, ending up costing me about the same as if I had bought a retail battery of equal performance. That meant that in the end I had a new battery and I considered all the tools as free. Since then I’ve used them to build countless more batteries and made some huge savings!
I would advise against connecting one battery to the other’s charging port. That charging port, as you correctly stated, is wired to a charging circuit on the BMS which is usually meant to take 5A max, sometimes less, whereas the discharging side of the BMS usually puts out at least 15A, sometimes much more. You can easily fry your BMS by connecting a second battery to its charge port.
Having built a 13s4p battery to the best of my ability and hooked it up to my 48V 1000W ebike conversion kit…. the lights on the throttle turned on and the wheel spun! Initially I thought the project was a success but after mounting the battery and controller onto the bike and taking the bike for a test spin I ran into a major problem.
Update: it looks like my nickel strips might be pure nickel after all. The salt water appears to have a suspension of brown precipitate which looks and smells like rust. However, after fishing the nickel strip out and rinsing it with water, it still appears to be silver in colour and not rusted:
Some individuals have lost considerable amounts of weight by using an electric bike. By making the biking terrain less of an issue, people who wouldn’t otherwise consider biking can use the electric assistance when needed and otherwise pedal as they are able. This means people of lower fitness levels or who haven’t cycled in many years can start enjoying the many health benefits E-bikes have to offer. 
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle’s crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle’s standard drive train. An electric mid-drive combined with a hub gear at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A stepless / coninuous ratio gear hub or a fully automatic gear hub may reduce the chocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional gear hubs.
I assume you mean 52V (14s, or 14 cells in series) which is a somewhat common lithium ion battery configuration. It works with most 48V setups but provides a little more power than a standard 48V (13s or 13 cell) battery. A good charger I recommend for 52V 14s batteries is this one.
7. Winner selection and notification: Winners of the Sweepstakes will be selected in a random drawing under the supervision of the Sponsor. Winners will be notified via e-mail to the e-mail address they entered the Sweepstakes with within five (5) days following the winner selection. Electric Bike Technologies LLC shall have no liability for a winner’s failure to receive notices due to winners’ spam, junk e-mail or other security settings or for winners’ provision of incorrect or otherwise non-functioning contact information. If the selected winner cannot be contacted, is ineligible, fails to claim the prize within 15 days from the time award notification was sent, or fails to timely return a completed and executed declaration and releases as required, prize may be forfeited and an alternate winner selected. The receipt by winner of the prize offered in this Sweepstakes is conditioned upon compliance with any and all federal and state laws and regulations. ANY VIOLATION OF THESE OFFICIAL RULES BY ANY WINNER (AT SPONSOR’S SOLE DISCRETION) WILL RESULT IN SUCH WINNER’S DISQUALIFICATION AS WINNER OF THE SWEEPSTAKES AND ALL PRIVILEGES AS WINNER WILL BE IMMEDIATELY TERMINATED.
hi i was considering adding a second set of batteries to my ebike in parallel to double the range but heared on a thread somewhere that this can damage/overload the controller which i suspect is a load of tosh but can anyone confirm/clarify this as i assumed the amp hour capacity was just that and the max amp output was just that, the maximum that can be drained at once, my understanding is it doesnt matter what amp hr the pack is as the amps drawn into the controller is governed by the demands of the motor which wont change if i have 2 packs connected.
This complete headset bearing set includes top and bottom head tube races, bearings in cage, crown race, cadjustable race, washer, and locknut. Head tube race bearing cup dimensions: 1-1/2″ (38mm) ID,…
I realize this isn’t as prescriptive as it could be, I think there are many models that could work for you but the sizing and possibly style are really up http://electricbikebatterys.com you. I’d love to hear how it works or possibly which ones you’re zooming in on and please, share your story in the forums to help others once you get an ebike and have time to ride it around. You can also call me using the contact page info to chat a bit if you’d like 🙂
Hi Bethany, glad you enjoyed the article and videos I’ve posted. Good question about dirt and dust… most ebike motors are sealed pretty well and can withstand light rain, dust etc. but should not be submerged or sprayed off directly, best to just use a damp rag to wipe them down. Depending on how much help you want up the hills and how much you and your bike weigh, you might be able to go with something light weight and simple like the Hill Topper or for more power and the addition of pedal assist you could get the BBS01 mid-drive kit which will cost more but offers great balance with a downtube battery. If you want even more power, they make a BBS02 which is 750 watts vs. 350. If you need help finding this or another kit just reach out and I’ll do my best to connect you.
Weight for weight, nickel-cadmium (NiCd) batteries have more capacity than lead-acid battery, and capacity is an important consideration on an electric bike. However, nickel- cadmium is expensive and cadmium is a nasty pollutant and hard to recycle. On the other hand, NiCd batteries will last longer than lead-acid batteries. But the reality is that because they are so hard to recycle or get rid of safely, NiCd batteries are rapidly becoming a thing of the past. These are also not a good choice of battery type, regardless of price.