Get the most out of your electric bike, folding bike or scooter with replacement parts and accessories available at NYCeWheels. Whether you are looking to add on to and upgrade your bike to make it more fun, efficient or stylish, or you simply… learn more
Before I seal my batteries in heat shrink, I like to wrap them in a thin layer of foam for added protection. This helps keep the ends of your cells from getting dinged if the battery receives any rough treatment, which can happen accidentally in the form of a dropped battery or ebike accident. The foam also helps to dampen the vibrations that the battery will experience on the bike.
I reached out to the company, because I’m very interested in this system. They currently only operate in Austria, Germany, and Switzerland, and the commented that they are only interested in slow growth. There is a Canadian reseller though, but I can’t find a site.
40% grade hills? That’s huge! You’ll definitely want a cell that can perform at high current since you’ll be pulling peak power from those cells to get up those big hills. Something like the Samsung 25R would be a good choice for this application.
The bigger decision for me is whether or not to go with a 29” or 27.5” wheel set. I believe Bulls in the US only offers a hardtail in the 29” size. There is a lack of information out there on the pros and cons for my particular application (i.e., 60/40 paved and rough dirt roads) specifically with regards to e-bikes. I know you prefer the 27.5 size as an “all-arounder”. At around 5’ 10.5” tall (barefooted) and 160 lbs, I most likely could find a good fit in either wheel size since Bulls offers at least three sizes in most of their bikes. Since I do not plan on commuting or doing much mountain biking, is one size better than the other for my rural mixed road use? Would there be any significant benefits with the larger wheels with regards to riding efficiency (i.e., less effort pedaling, improved battery life, etc.) or does the mid-drive motor make this mostly a non-issue? Not yet having ridden these e-bikes, my gut feeling is it may just come down to fit and preference. I would be interested in what you think based on your experience.
Fat tires aren’t just for sand and snow, cruise your city with the @igoelectric Folding Fat! #foldingfatbike #fatbike #fattiesfitfine #fatbikelife #foldingbike #ebike #electricbike #electricbikes 02.02.2018 – 19:56
Have you been searching for a durable and practical bicycle power-driven refit kit?. What’s more, it is produced by the sophisticated technology. And with the great quality, the bicycle power-driven refit kit is a durable and helpful for you to refit your bicycle!
7. Winner selection and notification: Winners of the Sweepstakes will be selected in a random drawing under the supervision of the Sponsor. Winners will be notified via e-mail to the e-mail address they entered the Sweepstakes with within five (5) days following the winner selection. Electric Bike Technologies LLC shall have no liability for a winner’s failure to receive notices due to winners’ spam, junk e-mail or other security settings or for winners’ provision of incorrect or otherwise non-functioning contact information. If the selected winner cannot be contacted, is ineligible, fails to claim the prize within 15 days from the time award notification was sent, or fails to timely return a completed and executed declaration and releases as required, prize may be forfeited and an alternate winner selected. The receipt by winner of the prize offered in this Sweepstakes is conditioned upon compliance with any and all federal and state laws and regulations. ANY VIOLATION OF THESE OFFICIAL RULES BY ANY WINNER (AT SPONSOR’S SOLE DISCRETION) WILL RESULT IN SUCH WINNER’S DISQUALIFICATION AS WINNER OF THE SWEEPSTAKES AND ALL PRIVILEGES AS WINNER WILL BE IMMEDIATELY TERMINATED.
If any one battery cell varies significantly from the others, do NOT connect it to the other cells. Paralleling two or more cells of different voltages will cause an instantaneous and massive current flow in the direction of the lower voltage cell(s). This can damage the cells and even result in fire on rare occasions. Either individually charge or discharge the cell to match the others, or more likely, just don’t use it in your pack at all. The reason for the voltage difference could have something to do with an issue in the cell, and http://electricbikebatterycharger.com don’t want a bad cell in your pack.
To shift optimally I suggest gaining speed then relaxing the force being applied to the pedals, shifting, then maintaining a gentle cadence until the chain is correctly aligned before exerting more force. This may be difficult on a pedelec system where the rider relaxes their input but the motor continues to pull hard. In this kind of situation it may be ideal to shift on a flat surface where little force is required to keep the bike moving forward. The problem here is that often shifting is done when encountering hills or starting from rest; just as more force is required to maintain speed. Long story short, be gentle when shifting and recognize that mid-drive motors pull the same chain that you do as a rider.
I’ve heard that newer hub motors have heat sensors to protect the system and they automatically shut themselves off if overloaded (is that what yours is doing?) mid-drives can be a great solution if you shift properly, it makes the job a lot easier for the motor (just like it does for you pedaling) and works pretty well in my experience.
The Flux ebike is neat and priced relatively low, it’s not a super large bike and won’t offer the same power as a 48 volt Pedego but it’s going to be lighter weight. Depending on your body size and weight it could work well enough and has the added benefit of mid-drive which frees up the front and rear wheels for easy maintenance. The downside is more shifting and higher forces on the chain, sprockets and derailleur. Have you checked out the Rad Power Bikes at all or maybe the VoltBike models? These companies ship internationally, have a large selection of styles and are priced pretty well. I hope this helps guide you, poke around the site here a bit and use the advanced search engine to narrow down by price, size, power etc. 🙂
I finally made it happen on BMS #3 (the unfortunate thing about AliExpress is that every dumb mistake that kills a part is another month added to the project) and the battery seems to work great, though it only has a couple miles so far.
What are some inexpensive controllers that can send more power to the GNG mid drive? I saw some guy on YouTube claiming that he got a $30 controller that handles 35-45 amps. I don’t see any $30 controllers on eBay.
I like to cut most of my nickel strip in advance so I can just weld straight through without breaking my flow to stop and cut more nickel. I measured out the width of three cells and cut enough nickel strip to weld the top and bottoms of 10 sets of 3 cells, meaning 20 strips of nickel that were each 3 cells wide, plus a couple spares in case I messed anything up.
Motor: We have a blog post showing some motor differences: https://www.ebikekit.com/blogs/news/its-whats-inside-your-motor-that-counts Cabling is probably the #1 issue when something goes wrong. Good connectors, good cables, and good assembly (bike shop!) are crucial Strain reliefs on all cable joints! Where you have a junction box or a connector, the stress is concentrated over a small area near this stiff spot on the cable. This can cause small breaks on the internal…
Bigger is better! And I know a better way batteries should be made. I use 560 of the Panasonic 18650b battery cells with 3.4AH per cell, wich in the end gave me (7kwh battery ebike!), that’s more than 300+ miles battery range easy. And I’ve learned that these batteries can be assembled like Lego blocks instead and eliminate harmful heat from soldiering, and wastful glueing. The benefit is a battery pack that can have removable, repairable, and reconfigurable battery cells! Its called (battery blocs) patiented by Shawn McCarthy. Unfortunatly its not the cheap method and requires a 3d printer to make. It spaces the cells slightly apart for better air cooling. Mine are packed into 4 PVC tubes run either at 103.6v or 51.8v. I believe along with some experts that a BMS is not required and can cause battery cells to fail early!, and a proper set voltage monitor and regulator prevents over discharge damage and you need to a timer and monitor the cell voltages with cell monitors while charging. Cooling setup would be a pluse to extend life. That’s all for now, best luck to all battery builders.
hi, recently, i try the BOSM intelligent torque sensor. its a miracle. It makes your ebike become a real ebike, like a human, it know your idea,you wanna fast,slow,climb mountain, across the grass , against the wind etc. It will adjust the output power intelligently.
If you don’t have an actual heat gun, you can use a strong hair dryer. Not all hair dryers will work, but my wife’s 2000 watt model is great. I own a real heat gun but actually prefer to use her hair dryer because it has finer controls and a wider output. Just don’t go mess up your wife’s hair dryer!